Marshall™
Knobs

We carry a complete selection of Marshall™ Amplifier parts for both vintage and modern amps.

Back to Marshall™ Amp Parts Index



Click on photo for
larger view
KNOB, Revisit™ Quality Reproduction of Marshall™ Knob, Push-on Knurled, Single Knob. Excellent quality aftermarket Marshall™ control knobs, push-on type.   Designed for the "knurled" type control shafts.   Found on a variety of Marshall™ amps, including some JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models. Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.   Especially true if your amp is ~20 years old or greater (JCM800 and JCM900, for example).     Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knob are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT
$1.89
(Single Knob)


Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 6.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 6 knobs.  Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.    Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.   Especially true if your amp is ~20 years old.  Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-6
$9.95
(Set of 6 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 10.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 10 knobs.   Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.     Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.   Older Marshalls typically have knobs where some of the gold caps have fallen off, and the other gold caps have faded to look more like silver than gold.    It used to be a bit pricey to swap out the complete set of knobs on some of the JCM900's, but with this new set of aftermarket Marshall™ knobs, it's affordable.    This set of 10 knobs is perfect for many JCM900 series models with 10 control pots, such as the 2101, 2501, 4100, 4101, 4102, 4500, 4501, and 4502.   Quality reproduction of the original Marshall™ knobs at half of the cost.  Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-10
$14.95
(Set of 10 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 11.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 11 knobs.  Designed for the "knurled" type control shafts (used on some JCM800s - check your particular amp to make sure it has knurled knobs and not solid smooth shaft pots with set-screw knobs).     Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.   Older Marshalls typically have knobs where some of the gold caps have fallen off, and the other gold caps have faded to look more like silver than gold.    It used to be a bit pricey to swap out the complete set of knobs on some of the split-channel JCM800's with 11 controls, but with this new set of aftermarket Marshall™ knobs, it's affordable.    This set of 11 knobs is perfect for many split-channel JCM800 series models with 11 control pots, such as the 2205, 2210, 4210, 4211, 4212, 5210, and 5212.  (Check your particular amp to make sure it has knurled knobs and not solid smooth shaft pots with set-screw knobs)  Quality reproduction of the original Marshall™ knobs at half of the cost.  Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-11
$15.95
(Set of 11 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 25.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 25 knobs.  Designed for the "knurled" type control shafts   Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.  Quality reproduction of the original Marshall™ knobs at half of the cost.  This set of 25 knobs is great for repair shops, at less than $1.00 per knob.    Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-25
$24.95
(Set of 25 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 50.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 50 knobs.  Designed for the "knurled" type control shafts   Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.  Quality reproduction of the original Marshall™ knobs at half of the cost.  This set of 50 knobs is great for repair shops, at less than 80 cents per knob.    Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-50
$39.95
(Set of 50 knobs)



Click on photo for
larger view
KNOB, Marshall™, PUSH ON D-SHAFT (Read applicable models!)
Standard original Marshall™ control knob, push-on type, for D-Shaft pots used in the following Marshall™ amp models:   DSL-20HR Head, DSL-50 Head, DSL-100 Head, TSL-60 Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo, MA-50H Head, MA-100H Head, MHZ-15 Haze 15.  Original Marshall™ part.   For the similar knob used on some ValveState models, DSL and TSL combos, MA Series Combos, and JVM series heads, see the R-MKDS-C knob elsewhere on this page.    
The MKDS Knob is constructed so that the pointer on the front of the knob is directly behind the flat spot in the shaft hole on the back side of the knob.

Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.   Especially true if your amp is ~20 years old.
Part #MKDS

$2.99
(Single Knob)



Click on photo for
larger view
Save with Multipack!  KNOB, Set of 6 Marshall™, PUSH ON D-SHAFT (Read applicable models!)
Standard original Marshall™ control knob, push-on type, for D-Shaft pots used in the following Marshall™ amp models:   DSL-20HR Head, DSL-50 Head, DSL-100 Head, TSL-60 Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo, MA-50H Head, MA-100H Head, MHZ-15 Haze 15.  Original Marshall™ part.   For the similar knob used on some ValveState models, DSL and TSL combos, MA series combos and JVM series heads, see the MKDS-C knob elsewhere on this page.   
The MKDS Knob is constructed so that the pointer on the front of the knob is directly behind the flat spot in the shaft hole on the back side of the knob.

Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.   Especially true if your amp is ~20 years old.
Part #MKDS-6

$14.95
(Set of 6 knobs)



 
KNOB, Revisit Marshall™, PUSH ON D-SHAFT (Read applicable models!)

Standard Revisit Marshall™ style control knob, push-on type, for D-Shaft pots used in the following Marshall™ amp models:   DSL-201 combo, DSL-401 combo, DSL-40C combo, TSL-122 combo, TSL-601 combo, TSL-602 combo, JVM205H head, JVM210H head, JVM410H head, VS15 combo, VS30R  combo, VS65R combo, VS100R combo, VS100RH head, VS102R combo, VS230 combo, VS265 combo, AVT20 combo, AVT50 combo, AVT50H head, AVT100 combo, AVT150 combo, AVT150H head, AVT275 combo, AS100D combo, MA50C Combo, MA100C Combo, MG10, MG15, MG15FX, MG30FX, MG50FX, MG100FX, MG100HFX, MG102FX.   For the similar knob used on DSL and TSL JCM2000 series heads, MA series heads, and JVM series combos see the MKDS knob elsewhere on this page.   The R-MKDS-C Knob is constructed so that the pointer on the front of the knob is 180 degrees away from the flat spot in the shaft hole on the back side of the knob.
Part #R-MKDS-C

$2.99
(Single Knob)



Click on photo for
larger view
KNOB, Revisit™ Quality REPRODUCTION of Marshall™, Set Screw.
Revisit™ aftermarket Marshall™ control knob, with gold cap and set screw.  Fits 1/4" shaft.  Similar to original Marshall™ set-screw knob.  This style of knob was used mainly in the 60s and 70s, and some JCM800 models from the early 80s. 

Comments on appearance and construction:  In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.  Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.   These knobs have a brass insert, so they tend to be more durable than the genuine all-plastic Marshall knobs.
Part #MKSS

$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB SET, Marshall™ type, Set Screw, Set of 6.
Revisit™ aftermarket Marshall™ control knobs, with gold cap and set screw.  Fits 1/4" shaft, set of 6 knobs.  Similar to original Marshall™ set-screw knob.   This style of knob was used mainly in the 60s and 70s and some JCM800 models from the early 80s. 

Comments on appearance and construction:  In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall™ knobs fade over time.  Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.   These knobs have a brass insert, so they tend to be more durable than the genuine all-plastic Marshall knobs.
Part #MKSS-6

$9.95
(Set of 6 knobs)
 

SET SCREW

Click on photo for
larger view
KNOB, Revisit™ Quality REPRODUCTION of Marshall™, Black Top, Set Screw.
Revisit™ aftermarket Marshall™ control knob, with black metal cap, brass insert and set screw.  Fits 1/4" shaft.  Similar to original Marshall™ set-screw knob used on the early Marshall models until the early 1980s.   Shiny ridged black metal top on black plastic body.
Part #MKBSS
$1.99
(Single Knob)
 

PUSH-ON

Click on photo for
larger view
KNOB, Revisit™ Quality REPRODUCTION of Marshall™, Black Top, Push-On.
Revisit™ aftermarket Marshall™ control knob, with black metal cap, push-on for knurled shaft pots, used on most Marshall models from the late 1980s to the present.  Similar to original Marshall™ push-on knobs.   Shiny ridged black metal top on black plastic body.
Part #MKBPT
$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB, Silver Marshall™ type, SET SCREW
Revisit™ aftermarket Marshall™ control knob, with silver cap and set screw.  Fits smooth 1/4" shaft.  Similar to original silver Marshall™ set-screw knob, which has been discontinued.  
Part #MKSSS
$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB, Silver Marshall™ type, PUSH ON
Revisit™ aftermarket Marshall™ control knob, with silver cap and designed to fit a "knurled" 1/4" shaft.   No set-screw. Similar to original silver Marshall™ knob, which has been discontinued.  
Part #MKSPT
$1.99
(Single Knob)
 


Click on photo for
larger view
MARSHALL POWER SWITCH BUTTON FOR VALVESTATE SERIES II AMPS  
Power switch button for the second ValveState series, including models VS15, VS30R, VS65R, VS100R, VS100RH, VS102R, VS230, VS232 AND VS265.   Also for the Bass State 150. Marshall reference numbers SW1008KNOPF.  Fits the SW-160 power switch.
Part #K-108
$2.50


Click on photo for
larger view
ROUND SWITCH CAP - FITS SW-212 and 090-0012-0
This is a black 5mm (approx 3/16") diameter X 9mm long switch cap which fits the SW-212 and 090-0012-0 Push Switches.   Exact replacement for most of the round caps used on the Gallien-Krueger 400RB-II, 700RB-II, 1001RB and similar models.     The diameter of this switch cap is smaller than the original round switch cap from Marshall™ found on some of the early ValveState models.  Does NOT fit the TSL/DSL amps in the JCM2000 series.    For switches with actuator shaft of 2.7mm square.

Part #K-212
$1.50  


Click on photo for
larger view
SQUARE SWITCH CAP - FITS SW-212
This is a black 5mm x 5mm (approx 3/16") square mini-switch cap which fits the SW-212 Marshall™ Push Switch (used primarily for channel switching).  Replaces the original S213 switch cap from Marshall™ , which has now been discontinued.   NOTE:   This is NOT the power switch cap on ValveState Amps.  Also, this switch cap does NOT fit the SW-650 switch.  This square cap is found on the Marshall™, 6100, 6101, JMP1, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612, JTM615, JTM622, 8010, AS80R, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280, and 9004 models.  For switches with actuator shaft of 2.7mm square.

Part #K-213
$1.50  


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov