Marshall™
Hardware

We carry a complete selection of Marshall™ Amplifier parts for both vintage and modern amps.

Back to Marshall™ Amp Parts Index



Click on photo for
larger view
MARSHALL™ SPRUNG FOOT FOR HEADS.  Genuine Marshall Sprung foot. Sold individually.  Screws are included  3 1/4" Long, 2" Wide, 1" Tall.   2-5/16" Mounting Centers. 
Part #MSF-252
$8.95
(each)


Click on photo for
larger view
MARSHALL™ ANTI-SKID TRAY FOR 1960A ANGLED CABINETS.  Genuine Marshall Anti-Skid Tray. Sold individually.   For the Marshall™ 1960A slant cabinets. Gold rivets are included.  9-7/8" Long, 3" Wide, 1/8" Thick.  With Marshall logo. 
Part #AST-1960
$18.65
(each)


Click on photo for
larger view
MARSHALL™ CASTER CUPS FOR 1960B STRAIGHT CABINETS - SET OF 4.  Genuine Marshall Caster Cups. Complete set of 4 for one cabinet.  Package of 4 includes 16 gold rivets.  For the Marshall™ 1960B straight cabinets.  3.9" Long, 2.07" Wide.
Part #MCC-1960
$18.95
(Set of 4)


Click on photo for
larger view
MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4.  
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for rack-mount amps, combo amps, or small speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter (wide end) x 3/4" diameter (narrow end) x 0.85" tall.  Mounting screws not included.  Set of 4 feet.   Good replacement for smaller Marshall amps, the 3203 Artist series, JTM60 series, etc.

Part #BRF-9105
$4.95
(pack of 4)
 


Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4
This heavy-duty rubber foot offers a sure grip on all types of surfaces.  Replacement for the feet on Marshall heads from the late 60s and early to mid 70s.  The integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter x 1" tall. Mounting screws not included.

Part #BRF-1691
$4.95
(pack of 4)
 


Click on photo for
larger view
MARSHALL™ HANDLE STRAP FOR MAH-294 HANDLE.  Original Marshall™ handle strap for the MAH-294 Handle. Sold individually.  Includes metal strap insert and rubber strap.   Genuine Marshall.   Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Save money by replacing only the worn strap!  Ends and clamps not included.
Part #MHS-294
$7.95
(each)


Click on photo for
larger view
MARSHALL™ END CAPS FOR MAH-294 HANDLE.  Handle end caps for the MAH-294 Handle. Sold in sets of two caps.   NOTE:  DOES NOT HAVE THE MARSHALL LOGO ON THE CAPS.   Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Save money by replacing only the parts the handle needs!  Strap, screws and clamps not included.   Set of two end caps.
Part #MHC-294-2
$4.95
(for a set of 2 end caps)


Click on photo for
larger view
MARSHALL™ INTERNAL END CLAMPS FOR MAH-294 HANDLE.  Handle internal clamps for the MAH-294 Handle. Sold in sets of two end clamps.   Genuine Marshall.   Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Save money by replacing only the parts the handle needs!  Strap, black end caps, screws and strap not included.   Note:  These are unfinished metal caps - designed to be used only with the snap-on MHC-294-2 end caps.  Set of two end clamps.
Part #MIC-294-2
$2.99
(for a set of 2 end clamps)


Click on photo for
larger view

Marshall™ METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™   MAH-294 handle.   Original Marshall™ , designed to work with the OEM metric T-Nuts.   Set of 2 Flat-head counter-sunk Phillips,  M5 x 0.8, length 25 mm.   Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
 


Click on photos for
larger view


(Assembled)

Marshall™ HANDLE
Genuine Marshall™ Handle for modern heads and combo amps.   Used primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Original Marshall™ part number M-PACK-00031.    Kit contains:

  • (2) Countersunk screws - M5 x 0.8, overall length of 25 mm

  • (2) Mounting brackets
  • (2) Black bracket covers with Marshall™ logo
  • (1) Rubber handle with metallic insert
  • Center-to-center screw mounting distance is 8 3/8" (213mm). 
  • Overall length of assembled and mounted handle is 101/4" (260mm).
  • Replacement screws are the Marshall™ SC-404 screws, below

Part #MAH-294

$19.95

 



Click on photos for
larger view


(Assembled)
Marshall™ AFTERMARKET HANDLE
Identical to the Genuine Marshall™ Handle MAH-294 (above), except does not have the "Marshall" name imprinted on the end caps.   Save over 40% compared to the price of the original Marshall™ handle.  For modern heads and combo amps.   Used primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Replaces Original Marshall™ part number M-PACK-00031 or stock number MAH-294.    Kit contains:
  • (2) Countersunk screws - M5 x 0.8, overall length of 25 mm
  • (2) Mounting brackets
  • (2) Black bracket covers (no Marshall™ logo)
  • (1) Rubber handle with metallic insert
  • Center-to-center screw mounting distance is 8 3/8" (213mm). 
  • Overall length of assembled and mounted handle is 101/4" (260mm).
  • Replacement screws are the Marshall™ SC-404 screws, below

Part #RAH-294

$10.99  


Click on photo for
larger view

Marshall™ METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™   MAH-294 handle.   Original Marshall™ , designed to work with the OEM metric T-Nuts.   Set of 2 Flat-head counter-sunk Phillips,  M5 x 0.8, length 25 mm.   Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
 



Click on photos for
larger view

VINTAGE Revisit™ REISSUE GOLD/BLACK HANDLE - Marshall™ JCM-800 style
Marshall™ Handle for vintage heads and combo amps.   Used on some early JCM800 series.    Kit contains:
  • (2) Mounting brackets
  • (2) Gold bracket covers
  • (1) Rubber handle strap with metallic insert
  • Center-to-center screw mounting distance is 9 inches between the inside two screws, and 10 inches between the outside two screws.
  • Overall length of assembled and mounted handle is 111/4" (286mm).
  • Mounting screws are included.

Part #MAH-287

$17.99  



Click on photos for
larger view

VINTAGE Revisit™ REISSUE SILVER/BLACK HANDLE - Marshall™ JCM-800 style
Marshall™ Handle for vintage heads and combo amps.   Used on some early JCM800 series.    Kit contains:
  • (2) Mounting brackets
  • (2) Silver color bracket covers
  • (1) Rubber handle strap with metallic insert, silver ends
  • Center-to-center screw mounting distance is 9 inches between the inside two screws, and 10 inches between the outside two screws.
  • Overall length of assembled and mounted handle is 111/4" (286mm).
  • Mounting screws are included.

Part #MAH-355

$17.99



Click on photos for
larger view

VINTAGE Revisit™ REISSUE GOLD/BLACK HANDLE REPLACEMENT STRAP - Marshall™ JCM-800 style
The strap part only of handle part number MAH-287.   Used on some early Marshall
JCM800 series amps.

Part #MHS-295

$10.95




Click on photos for
larger view

VINTAGE Revisit™ REISSUE GOLD HANDLE END CAP - Marshall™ JCM-800 style
One end cap only of handle part number MAH-287.   Used on some early Marshall
JCM800 series amps.   Sold individually.   Note:   We urge you to also replace the MIC-295 internal clamp at the same time.   These end caps may not lock securely on old internal clamps, making the end caps randomly pop off when lifting the amp by its handle.

Part #MHC-295

$1.95
(for one end cap)

Quantity:



Click on photos for
larger view

VINTAGE Revisit™ REISSUE HANDLE INTERNAL CLAMP - Marshall™ JCM-800 style
One internal clamp only of handle part numbers MAH-287 or MAH-355.   Used on some early Marshall
JCM800 series amps.   Sold individually.

Part #MIC-295

$1.00
(for one clamp)

Quantity:



Click on photos for
larger view

VINTAGE Revisit REISSUE GOLD/BLACK HANDLE - JMP, JTM "PLEXI"
Handle for vintage Marshall™ heads and combo amps.   Replacement for the original Marshall™ JMP, JTM "Plexi" series.    Kit contains:
  • (2) Mounting brackets
  • (2) Gold bracket covers
  • (1) Rubber handle strap with metallic insert
  • Center-to-center screw mounting distance is 9".
  • Overall length of assembled and mounted handle is 10.7" (272mm).
  • Mounting screws are NOT included

Part #MAH-288

$22.95  


Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC, 6" LONG
The mini Marshall™ logo - smallest size.    As used on the DSL201 combo, DSL401 combo, some of the smaller sized MG series combos, VS15, VS30R, 1912 Cab, JCM600, JCM602, AS50, 3005, 4501, 5005, 8010, 8015, MG10, MG10MKII, MG15RCD, MG30RCD, MG215RCD, TSL602, JCM3005, and some other models.    This logo is 6" long - please measure the old logo in order to ensure that you order the correct size.
Part #ML-601
$29.95  


Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC, 9" LONG
The 9 inch long Marshall™ logo - medium size.    As used on the 1922, TSLC212, 4203, 4502, 5002, 5010, 5205, 8020, 8040, 8100, AVT50, AVT50H, AVT150, JVM410, MG412A, 2266C, VS100RH, VS102R, VS112, VS230, VS232, VS265, TSL122, 5275, B150, 3203, MG100RCD,  and some other models  This logo is 9" long - please measure the old logo in order to ensure that you order the correct size.   Does NOT fit most Marshall™ heads, does NOT fit the larger MG series amps.
Part #ML-901
$34.95  


Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC, 11" LONG
The 11 inch long Marshall™ logo - large size.  As used on the 2100, 2205, 2203, 2204, 2210, 2550, 2553, 2554, 2558, 4102, 4001, 4210, 4211, 4212, 4100, 4101, 4103, 4010, 4500, 5213, 5210, 5212, DSL100,  1986, 1960B cabinet, 1959JMP, 1936, TSL100, 6100, 6101, JCM1959, 2558V, 3005, 2555SL, AS1960, 2100SLX, TSL60, 1987JCM,  DSL50, 3005, 1960AX,  and some other models  This logo is 11" long - please measure the old logo in order to ensure that you order the correct size.   
Part #ML-1101
$37.95  


Click on photo for
larger view
Marshall™ REAR VENT, GOLD MESH, JTM AND JMP SERIES

NOTE:  This is NOT the top vent!
This original Marshall vent is for the H-shaped head back panels on the vintage JMP and JTM amps from the 1960s.   Check the measurement on your back panel - the MV-210 vent measures 16 7/8" x 2 1/4". 
Part #MV-210

$34.95  


Click on photo for
larger view
Marshall™ TOP VENT, 8 SCREW OR RIVET HOLES, MOST JCM800 AND JCM900 HEADS
This original Marshall vent is for most JCM800 and JCM900 heads from the 1980s and 1990s.   Check the measurement of your existing vent - the MV-211 vent measures 17 5/8" x 3".  Rivets/screws not included.
Part #MV-211
$13.95  


Click on photo for
larger view
Marshall™ TOP VENT, POP-IN, FOR CERTAIN VALVESTATE AVT MODELS
This original Marshall vent is for the AVT50, AVT100, and AVT275 heads and combos.   Replaces the plastic vent immediately behind the handle, and is roughly the size of the handle. Check the measurement of your existing vent - the MV-218 vent measures 10 1/4" x 1 9/16"
Part #MV-218
$8.95  


Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC
Replacements for the standard M6 metric screws used to hold the chassis in virtually every Marshall™ head.  Washers included.   Package of 4 stainless steel screws, with 4 washers.  
Part #MCB-4
$3.99
(Set of 4 screws w/washers)
 



Click on photo for
larger view
STAINLESS STEEL COMBO CHASSIS SCREWS, Marshall™ METRIC (NOT BLACK!)  SET OF 4 SCREWS.
Unpainted replacements for the standard M6 metric screws used to hold the chassis in virtually every larger Marshall™ combo (typically 50 watts & up).   Note that these screws are plain stainless steel - NOT BLACK LIKE the ORIGINALS.  You may paint the top black if you choose.  We recommend that you only paint the top - do not paint the threads.  35mm long, replaces Marshall part number MESCRW00001.   Found in the JTM610, JTM612, JTM612, JTM615, JTM622, JCM601, JCM602, 2101, 2501, 2502, 4101, 4102, 4501, 4502, TSL601, TSL601, and TSL122.   Washers not included, washers unavailable.   Set of 4 screws.
Part #MCS-5140-4
$2.29
(Set of 4 screws)


Click on photo for
larger view
Marshall™ CHASSIS WASHERS
Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™ head.   Note:  Not for Marshall Combo amps.   Also fits Orange and Trace Elliot amps which use chassis bolts to secure the chassis.  Package of 4 washers.
Part #MCW-4
$1.99
(Set of 4 washers)
 


Click on photo for
larger view
CHASSIS CAGE NUTS, Marshall™ M6 METRIC
Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head.   Package of 4 cage nuts.   Mates with the MCB-4 or MCS-5140-4 screws, above.
Part #MCN-4
$4.59
(Set of 4 nuts)
 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR CLOSED BACK CABINETS (SUCH AS Marshall™ ).  Set of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with either the CW-400 or CW-501 cup washers.
Part #
SC-400-8
$1.99
(for a pack of 8 screws)

 
 



Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 17) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman, Bandmaster, etc ).  Set of 17 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with the CW-400-17 cup washers.   A set of 17 screws completely replaces all of the screws on most Marshall™ 4x12 cabinets, including the 1960 models.
Part #
SC-400-17
$3.89
(for a pack of 17 screws)

 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 8.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 8 washers.
Part #CW-400-8
$1.95
(for a set of 8 washers)
 


Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 17.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 17 washers.  Some of the larger Marshall 4x12 cabinets, such as certain model 1960 cabinets, have 17 screws and washers in the back panel.
Part #CW-400-17
$3.79
(for a set of 17 washers)
 



Click on photo for
larger view
Marshall™ HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS (SET OF 4) FOR FULL SIZE HEADS.  Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.  Fits most large Marshall™ heads starting in the 1980s, including the JCM-800, JCM-900, JCM-2000 and JVM series.   Note:  The screw heads in this package have a slight oval shape, as opposed to many Marshall™ head back panel screws which have a flat head.  This oval shape helps improve the "bite" of the screwdriver, and helps prevent the screw head from being mangled over time.
Part #
MBP-4
$1.49
(for a pack of 4 screws and 4 washers)
 


Click on photo for
larger view
Marshall™ SMALL BRASS PAN-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6).   Set of 6 screws, brass, 3/8" (9.5mm) long, slotted pan head - head is 5.4mm in diameter, 4-40 thread, with lock washer and nut.   Used to mount preamp tube sockets and impedance selectors in classic Marshall amps.
Part #
MSBS-6
$1.99
(for a pack of 6 screws, 6 lock washers and 6 nuts)
 



Click on photo for
larger view
Marshall™ SMALL BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6).   Set of 6 screws, brass, 1/2" (12.7mm) long, slotted round head - head is 5.4mm in diameter, 4-40 thread, with lock washer and nut.   Used to mount impedance selectors and IEC power cord connectors in classic Marshall amps.
Part #
MLBS-6
$2.49
(for a pack of 6 screws, 6 lock washers and 6 nuts)
 



Click on photo for
larger view
Marshall™ MEDIUM BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 8).   Set of 8 screws, brass, 3/8" (12.7mm) long, slotted round head - head is 6.1mm in diameter, 6-32 thread, with lock washer and nut.   Used to mount power tube sockets, capacitor cans and ground lugs in classic Marshall amps.
Part #
MMBS-8
$2.99
(for a pack of 8 screws, 8 lock washers and 8 nuts)
 


Click on photo for
larger view
Ground Lug Terminals - Angled
Made from tin-plated brass - will not rust.   Used to connect a ground wire to a screw and nut on a chassis.  Angled, with two holes for soldering wires.   With built-in lock washer to keep the screw and nut from loosening.   Designed for a #8 size screw.   Pack of 5 terminals.

Part #GL-113
$1.39
(Pack of 5 terminals)

 



Click on photo for
larger view
TERMINAL STRIPS, 6 LUG, SET OF 2.   Perfect for amplifier circuit additions or modifications.   Center post for mounting to chassis.   All 6 terminals are isolated from ground.  Each terminal strip is 2-5/8 inches long.   The lugs are set on 3/8 inch centers.   Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug.   Set contains 2 terminal strips as pictured.   Mounting hardware not included.
Part #TS-825
$2.99
(for a set of 2 terminal strips)



Click on photo for
larger view
TERMINAL STRIPS, 7 LUG, SET OF 2.   Perfect for amplifier circuit additions or modifications.   End terminals on each strip are the mounting lugs, so they become a ground lug if attached to a metal chassis.   Each terminal strip is 2-5/8 inches long.   The lugs are set on 3/8 inch centers.   Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug.   Set contains 2 terminal strips as pictured.   Mounting hardware not included.
Part #TS-712
$3.69
(for a set of 2 terminal strips)


Click on photo for
larger view
PC BOARD STANDOFF, NYLON, MARSHALL STYLE    This style of PC board standoff is used in a number of amplifiers.  Designed for a 4.5mm hole in the chassis, and a 2.5mm hole in the PC board.   Total height of standoff is 26.3mm (just over 1 inch).   Supports the PC board at a height of 15.8mm (5/8 inch) above the chassis.  Set of 4 standoffs in the kit.

Part #
PCS-15
$1.99
(for a set of 4 standoffs)
 

CAPACITOR CLAMP, for FT-1616, FT-3232, FT-5050, RG-5050, JJ-5050, or other 1 3/8" diameter can style capacitors.

Part #CC-122

$2.50  


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2022 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov