Peavey Jacks
>
 
Click on photo for
larger view
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING.  
Both tip and ring conductors are switched (normally closed).  5 pins.    Original Peavey® part number 31466217.  Found in most Peavey
® Vyper® models as the input jack.  Replaces Switchcraft 114BPCX and 114BPCSX.  Nut and washer included.

Part #J-217
$3.95  

 
Click on photo for
larger view
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.   Both tip and ring are switched (normally closed).   Used in Peavey® and other brands.  Same as J-114BPC, except that the threads are insulated.  Nut and washer included.   This version has standard wide pins for insertion into PC board.   See the J-527 for narrow pins for small PC board holes.

Part #J-523
$6.95  

 

Click on photo for
larger view
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.   Both tip and ring are switched (normally closed).   Used in Peavey® and other brands.  Same as J-523, except that the pins are narrow for insertion into smaller PC holes.  Nut and washer included.

Part #J-527
$5.95  

 

Click on photo for
larger view

JACK, 1/4", Peavey® ORIGINAL, DUAL TIP HID, PC MOUNT, MONO, 4 PINS (WIDE PINS).  SPECIAL APPLICATION!! 
This jack is for use in Peavey® products only, and is unusual in that two different pins contact the tip of the plug.  One of the tip contacts is switched (normally closed), and the other tip contact is open.  The pins on this jack are wide (1.7mm), so the hole in the PC board must be large enough to accept the pin.   For the same jack with narrow pins, see the J-214.   This jack is exclusive to Peavey®.  Peavey part number 71466032 or 31466032.  Used for a variety of functions on Peavey products, including input jacks.  Nut and washer included.
Part #J-521
$4.95  

 

Click on photo for
larger view

JACK, 1/4", Peavey® ORIGINAL, DUAL TIP HID, PC MOUNT, MONO, 4 PINS (NARROW PINS).  SPECIAL APPLICATION!! 
This jack is for use in Peavey® products only, and is unusual in that two different pins contact the tip of the plug.  One of the tip contacts is switched (normally closed), and the other tip contact is open.  The pins on this jack are narrow (1.1mm).  For the same jack with wide pins, see the J-521.  This jack is exclusive to Peavey®.  Peavey part number 71466214 or 31466214. Used for a variety of functions on Peavey products, including input jacks. Nut and washer included. Found in the Classic 20, Classic 30, Delta Blues, and some Ecoustic models, among others.
Part #J-214
$4.95  

 

Click on photo for
larger view

JACK, 1/4", Peavey® ORIGINAL, DUAL TIP HID, PC MOUNT, MONO, 4 PINS, INSULATED.   SPECIAL APPLICATION!! 
This jack is for special applications in Peavey® products only, and is unusual in that two different pins contact the tip of the plug.  One of the tip contacts is switched (normally closed), and the other tip contact is open.  This jack is exclusive to Peavey®.   Same as J-521 except that the threads are insulated.  Nut and washer included.

Part #J-522
$3.95  

 

Click on photo for
larger view

JACK, 1/4", Used in Peavey®, PCB, MONO CLOSED CIRCUIT
PCB mono closed circuit.   Original Peavey part numbers 31466164, and
71466164.  Found in the Peavey® KB60, Studio Chorus 210, some versions of the Basic 112, Micro Bass (original version), Rage 158, and other models.  Includes nut and washer.

Part #J-525
$7.95  

 

Click on photo for
larger view
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.    Original Peavey part number 31466167 and 71466167. Used as the headphone jack in the KB/A 60 keyboard amp.  Also found in some other Peavey products.  Insulated bushing for ground isolation from the chassis. Nut and washer included.

Part #J-526
$5.99  

 

Click on photo for
larger view
JACK, 1/4", PC MOUNT, STEREO, 6 PINS, SWITCHED, INSULATED.    Original Peavey part number 31466165 and 71466165.  Found in some versions of the 5150, 6505, 5150-II and 6505+, as well as the pre-EQ jack on the KB60.  Used as the input jack on the older version of the Basic 112.  Nut and washer included.

Part #J-625
$7.99  


Click on photo for
larger view
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®
Found in many guitars, effects pedals, amps speaker output.  Includes nut and washer.
Part #J-11
$2.99


Click on photo for
larger view
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING
Same as the J-11 jack, but with longer (3/8") threaded bushing for mounting in thicker panels.  Includes nut and washer.
Part #J-L11
$4.25


Click on photo for
larger view
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING, ISOLATION WASHERS
Same as the Switchcraft L11 but includes fiber isolation washers. The isolation washers keep the jack from making contact with your chassis. This leaves the jack ungrounded which is needed in certain applications.

Part #J-L11W
$4.49


Click on photo for
larger view
JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft®
Peavey part number 71466004.
Part #J-12A
$3.59


Click on photo for
larger view
JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft®, LONG BUSHING
Same as the J-12A jack, but with longer (3/8") threaded bushing for mounting in thicker panels.  Includes nut and washer.
Part #J-L12A
$3.95


Click on photo for
larger view
JACK, 1/4", MONO, TIP SHUNT, WIRED, Switchcraft®, LONG BUSHING, ISOLATION WASHERS
Same as the Switchcraft L12A jack but includes a set of isolation washers. The isolation washers keep the jack from making contact with your chassis. This leaves the jack ungrounded which is needed in certain applications.   Commonly used in older Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville amps to replace the fragile input jacks.
Part #J-L12AW
$4.49


Click on photo for
larger view
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®
Used with T/R/S plugs for either balanced connections or stereo connections.   Also very common in guitars with active pickups, and as the input jack on some effects pedals.   The ring conductor is used in these cases to "turn on" the battery by tying one leg of the battery to ground via the plug. 
Part #J-12B
$3.95


Click on photo for
larger view
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING
Same as the J-12B jack, but with longer (3/8") threaded bushing for mounting in thicker panels.  Includes nut and washer.
Part #J-L12B
$6.95


Click on photo for
larger view
JACK, 1/4", TIP-SLEEVE, WITH TRANSFER SWITCHING.  Switchcraft 13A Jack.
Used with for special switching applications - the tip contacts one terminal when no plug is inserted, and contacts a different terminal with the plug in place.   Used in
a number of Fender® models, both vintage and modern as the extension speaker jack (ex: Blues and Hot Rod Deluxe and Deville models).  Original Fender® part number 0041701000 (originally 042701).   Also found in some Peavey amps, such as the Classic 50 speaker jack.  
Part #J-13A
$8.99


Click on photo for
larger view
JACK, 1/4", TIP/RING/SLEEVE, WITH TIP SHUNT.  Switchcraft 13B Jack.
Tip/Ring/Sleeve Switchcraft jack.   Tip has a shunt contact, ring contact is open circuit.

Part #J-13B
$7.95


Click on photo for
larger view
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE
Stereo jack. 6 PC board terminals, switched.  With nut and washer.  British style.
Part #J-504
$1.89  


Click on photo for
larger view
SAVE WITH MULTIPACK!  JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE, PACK OF 6
Stereo jack. 6 PC board terminals, switched.  Pack of 6 jacks, with nuts and washers.
Part #J-504-6
$10.99
(Set of 6 jacks)
 


Click on photo for
larger view

SAVE WITH OUR MULTIPACK ASSORTMENT!  THIS PACK CONTAINS THREE J-503 (4 PIN) AND THREE J-504 (6-PIN) JACKS.  
Many amps contain both the 4 pin and the 6 pin British jacks.   This assortment gives you 3 of each jack ...  Three J-503, and three J-504.  

Part # J-5034-6

$10.49
(For 3 J-503 Jacks and 3 J-504 Jacks)


Click on photo for
larger view
JACK, 1/4", T/R/S PC MOUNT PLASTIC, BRITISH STYLE, WITH EMI/RFI GROUND WASHER.
Same as the J-504, with the addition of a special ground washer which contacts the chassis AND is inserted into the ground connection of the PC board via dual pins under the jack.   6 PC board terminals for signal, plus 2 additional terminals for the ground washer.   Only for amplifiers so equipped for this jack, designed
to reduced EMI/RFI interference (radio stations, ground loops).  Found in some Marshall solid state amps, as well as other brands.   Note:  Must be used only on amps designed for this type of jack that have the PCB holes to accept the pins of the ground washer.  Nut is included.
Part #J-504GW
$2.89  


Click on photo for
larger view
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE - WHITE   Identical to the J-504 above, except in white.  How cool is that!  Stereo jack. 6 PC board terminals, switched.   With nut and washer.
Part #J-556
$3.99  


Click on photo for
larger view
JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE
 
4 PC board terminals, switched.  Used in many brands of amps and other equipment.   With nut and washer. 
Part #J-503
$1.89  


Click on photo for
larger view
SAVE WITH MULTIPACK!  JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE, PACK OF 6
4 PC board terminals, switched.  Used in many brands of amps and other equipment.   Pack of 6 jacks, with nuts and washers. 
Part #J-503-6
$9.99
(Set of 6 jacks)
 


Click on photo for
larger view
JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH NICKEL-PLATED NUT AND CHROME TRIM RING
4 PC board terminals, switched.  Used in many brands of amps and other equipment.   Same footprint as J-503 jack - may be used in place of J-503 to add a touch of "chrome" class to your amp!  Used in newer Mesa Boogie amps, including the Rosette, Mini Rectifier, Mark 5:Twenty-Five, etc.
Part #J-603
$2.79
(per jack)
 


Click on photo for
larger view
JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE, WITH EMI/RFI GROUND WASHER.
Same as the J-503, with the addition of a special ground washer which contacts the chassis AND is inserted into the ground connection of the PC board via dual pins under the jack.   4 PC board terminals for signal, plus 2 additional terminals for the ground washer.   Only for amplifiers so equipped for this jack, designed
to reduced EMI/RFI interference (radio stations, ground loops).  Found in some Marshall solid state amps, as well as other brands.   Note:  Must be used only on amps designed for this type of jack that have the PCB holes to accept the pins of the ground washer.  Nut is included.
Part #J-503GW
$2.59  


Click on photo for
larger view
JACK, 1/4", MONO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE - WHITE   Identical to the J-503 above, except in white.  How cool is that!  Mono input jack. 4 PC board terminals, switched.  With nut and washer.
Part #J-555
$3.99  


Click on photo for
larger view

JACK, 1/4", TIP/RING/SLEEVE 6-PIN, PC MOUNT, Peavey® AMPS
Peavey
® PCB mount 1/4" jack. Stereo, 6 pin. Fits certain Peavey® amp models.  Peavey part number 71466323.  Black nut is included.  For savings on multiple jacks, see J-518-6 below.  
Part #J-518

$3.50


Click on photo for
larger view

SAVE WITH MULTIPACK!   JACK, 1/4", TIP/RING/SLEEVE 6-PIN, PC MOUNT, Peavey® AMPS, SET OF 6 JACKS.
Peavey
® PCB mount 1/4" jack. Stereo, 6 pin. Fits certain Peavey® amp models.  Peavey part number 71466323.  Black nuts are included.  Set of 6 jacks. 
Part #J-518-6

$14.95
(For Set of 6 Jacks)


Click on photo for
larger view

JACK, 1/4", MONO 4-PIN, PC MOUNT, Peavey® AMPS
Peavey
® PCB mount 1/4" jack. Tip/Sleeve, 4 pin. Fits certain Peavey® amp models.   Peavey part number 71466322.  Black nut is included.   For savings on multiple jacks, see the J-519-6 jack set below.
Part #J-519

$2.95


Click on photo for
larger view

SAVE WITH MULTIPACK!  JACK, 1/4", TIP/SLEEVE 4-PIN,  PC MOUNT, Peavey® AMPS, SET OF 6 JACKS.
Peavey
® PCB mount 1/4" jack. Tip/sleeve, 4 pin. Fits certain Peavey® amp models.   Peavey part number 71466322.  Set of 6 jacks, black nuts are included. 
Part #J-519-6

$14.95

 

Click on photo for
larger view

JACK, 1/4", MONO, PC MOUNT, SHORT THREAD, PEAVEY
PCB mount 1/4" jack. Mono, 4 pin, PC board mount. Used in several versions of the Peavey ValveKing amplifiers, the MP4 Plus Powered Mixer, and the newer versions of the Basic 112.  Nut is included.   Peavey part number 71466222 and 31466322.

Part #J-661

$ 3.79
(per jack)

 

Click on photo for
larger view

JACK, 1/4", STEREO, PC MOUNT, SHORT THREAD, PEAVEY
PCB mount 1/4" jack. Mono, 6 pin, PC board mount. Used in several versions of the Peavey ValveKing amplifiers.   Also used in the Tour TKO Amp.  Peavey part number 31466323.  Nut is included.

Part #J-662

$ 3.99
(per jack)


Click on photo for
larger view
JACK NUT, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OTHERS.   Note:     Replaces most black plastic jack nuts EXCEPT for Roland.    Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks.   Also fits the J-518 and J-519 jacks.
 Part #J-5NT
$0.50  


Click on photo for
larger view
JACK NUT MULTI-PACK - SAVE!   6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OTHERS.   Note:     Replaces most black plastic jack nuts EXCEPT for Roland.    Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks.   Also fits the J-518 and J-519 jacks.
 Part #J-5NT-6
$2.39  


Click on photo for
larger view
JACK NUT, PLASTIC, BRITISH STYLE, WHITE
Replacement nut for the J-555 and J-556 jacks. 
Will also fit the J-502, J-503, J-504, J-505, J-503L, J-504L, J-518 and J-519 black jacks, if you wish to create a two-tone effect.
Part #J-5NTW
$0.60  


Click on photo for
larger view
JACK, CHASSIS MOUNT, DIN, 6 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps.  Also used by Genz Benz and other manufacturers.

Part #J-520 
$3.99  


Click on photo for
larger view
JACK, CHASSIS MOUNT, DIN, 7 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps.  Also used by Mesa Boogie, Genz Benz and other manufacturers.

Part #J-516
$3.99  


Click on photo for
larger view
JACK, CHASSIS MOUNT, DIN, 8 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps.  Also used by Genz Benz and other manufacturers.

Part #J-528
$3.99  


Click on photo for
larger view
SAVE WITH MULTIPACK!  JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4" jacks.  Does NOT fit the 24mm Marshall® pots.   Set of 6 washers and 6 nuts. 
Part #JNUT-38-6
$4.50
(Set of 6 washers and 6 nuts)
 

JACK NUT AND WASHER, METAL, SWITCHCRAFT®
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4" jacks.  Does NOT fit the 24mm Marshall® pots.  
Part #JNUT-38
$0.89
(Set of 1 washer and 1 nut)
 


Click on photo for
larger view.   Jack is in the picture to demonstrate how the washers are installed - jack is NOT included with the washers.
INSULATING SHOULDER WASHER, FIBER
Pair of fiber insulating shoulder washers for Switchcraft jacks with metal bushings.   Used to mount standard jacks in a 1/2" diameter chassis hole, while insulating the metal bushing (ground) of the jack from the chassis.   ID 3/8", OD 1/2".  Works great when replacing isolated plastic jacks with a more durable metal jack, which is frequently done on the input jacks of the Fender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe.   Two washers are used on each jack, and the "shoulders" are placed facing each other through the chassis.   The washers not only isolate the ground of the jack electrically for noise reduction, but also stabilize the jack in the 1/2" diameter hole.   Jack shown in picture NOT included.   Works well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13, J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks.
Part #ISW-3069
$0.49
(For a pair of washers.  Each jack needs two washers.)
 


Click on photo for
larger view
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING, ISOLATION WASHERS
Same as the Switchcraft L11 but includes fiber isolation washers. The isolation washers keep the jack from making contact with your chassis. This leaves the jack ungrounded which is needed in certain applications.

Part #J-L11W
$4.49



Click on photo for
 larger view
Revisit™ 18 GAUGE COPPER BONDED RED/BLACK ZIP CORD
Make low-cost, efficient speaker cables with this color-coded 18 gauge dual zip cord.   Red and black for easy polarity identification.  Resistance is 0.0097 ohms/ft.  Automotive grade "GPT" PVC insulation, oil and gas resistant, rated for -20 deg F to +160 deg F. Also perfect for bias testers, radio, home theatre, automotive, stereo, robotics, and model train applications.   Priced per foot, sold in lengths from 1 foot to 50 feet.
Part #RBZ-18
$0.32
(priced per foot)
 

Feet (1-50):



Click on photo for
 larger view
Revisit™ SPEAKER JUMPER CABLE
polyvinyl insulated silver plated copper speaker wire, 18 gauge, twisted pair, black and white.   Terminated at each end in standard 3/16" speaker fast-on connectors.   Great for connecting speakers in parallel in 2x12 or 4x12 cabinets.   24 inches (61 cm) long.   Made in USA.
Part #SJ-150
$5.99  



Click on photo for
 larger view
Revisit™ SPEAKER HARNESS
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.    Used to replace speaker cable in most combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4" jack and plug.   18ga black zip cord, right-angle plug and fast-on connectors for attachment to one speaker.  
Part #SCH-280
$6.99  


Click on photo for
larger view

JACK PLATE FOR SPEAKER CABINET, BLACK METAL, DUAL BRITISH 1/4"
This is a tough, durable 1.2mm Black Oxide Steel recessed jack plate, with two British J-502 jacks  installed.   Also included are four #8 x 3/4" black mounting screws.   Wire not included.    Dimensions: 3-1/2" x 5-1/8".    See full dimensions here

Part #JPC-344B

$7.95


Click on photo for
larger view
JACK PLATE, BLACK METAL, SINGLE 1/4" JACK, 2" OUTSIDE DIAMETER. Similar in style to vintage Fender® jack plates.  Works well with the Switchcraft J-11 1/4" jacks that we carry. Hole is 3/8", for most Switchcraft type jacks.  Easy to install, economical.   Includes 3 black oxide coarse-thread mounting screws, #6x3/4".   Jack not included - order separately.   For size specifications, click here.
Part #JP-180
$1.89



Click on photo for
larger view
Revisit™ JACK PLATE COMPLETE WITH SWITCHCRAFT #11 JACK.  Switchcraft #11 jack preinstalled with lock washer and trim washer. Outside diameter 2 inches (51mm). Minor assembly required. Designed to fit flush against a 1 1/8" (29mm) cabinet hole. Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to jack and speaker, attach plate to cabinet.
Part #JPC-180
$4.95



Click on photos for
larger views

JACK PLATE, MONO/STEREO, PLUG AND PLAY
This unit eliminates the confusing switch found on most stereo cabinets. Just pick your impedance and plug in. Labels shows the common 4 or 16 Ohm Mono and 8 Ohm Stereo option. Ready to install with a steel dish, wires, and speaker connectors already assembled - as shown in the photo.  Requires a 3 inch x 3-7/16 inch rectangular hole cut in the cabinet.  Direct easy replacement for many existing small jack dishes.   No soldering required.  Complete wiring directions included - click here for more details.  Designed to be used with 2x12 cabinets containing two 8-ohm speakers, 4x12 cabinets with four 16-ohm speakers, or 4x12 cabinets with four 4-ohm speakers.  Can be used for the following configurations:
  • 4 ohm mono
  • 8 ohm left + 8 ohm right stereo
  • 8 ohm left only mono
  • 8 ohm right only mono
  • 16 ohm mono

Part #CJP-1

$35.95


Click on photo for
larger view
Peavey binding post, pc mount, black.   Found on several models of Peavey power amplifiers.   Red type also available, below.  Fits standard banana plugs.
Part #BP-277
$6.50  


Click on photo for
larger view
Peavey binding post, pc mount, red.   Found on several models of Peavey power amplifiers.   Black type also available, above.  Fits standard banana plugs.
Part #BP-278
$6.50  


Click on photo for
larger view
JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR PC BOARD (SOLDER PINS).   Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Peavey®.

Part #J-NL4MD-V
$4.95  


Click on photo for
larger view
JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR WIRE ATTACHMENT (3/16" PUSH ON CONNECTORS OR SOLDER TABS).   Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Peavey®.

Part #J-NL4MP
$4.95  


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2022 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov