Capacitor Kits
for Vintage Marshall®, Music Man® and Fender® Amps



Featuring quality F&T®, TAD®, Ruby Gold®, MOD®, Illinois Capacitors® and other fine brands.

Capacitor values have changed slightly over the years due to changing manufacturing standards.   In some cases, 5uF has been replaced with 4.7uF.   Many 20uF and 25uF have been replaced with 22uF.    With F&T capacitors,  70uF has been replaced with 80uF.    On Ruby Gold capacitors in our standard kits, the polarity of the capacitor is indicated only by an arrow on the side of the capacitor which points toward the negative end.   On Ruby Gold capacitors, both ends of the capacitor are "dimpled", so you cannot determine polarity that way.

Due to improvements in technology, new capacitors are often about 50% smaller than original capacitors.

Disclaimer:   Fender occasionally made changes to designs which are not consistent with the model version on the tube chart.  Especially in the "silverface" years, the internal designs sometimes do not correspond with the schematic for the particular model version shown on the tube chart.    It is recommended that the values of the filter capacitors inside the capacitor housing beneath the chassis be checked and verified before ordering a specific capacitor kit, to make sure that your amp was not one that did not adhere to the schematic.

WARNING:   Tube amplifiers contain high voltage which is stored in the filter capacitors even after the amplifier has been turned off.   Always unplug the amplifier from commercial power, and discharge all filter capacitors before working on the amplifier circuitry.   If you are unsure about this procedure, we strongly recommend that you leave your amplifier in the care of a professional service person.

Marshall Kits     Music Man Kits      Fender Kits     Crate Kits     Peavey Kits

  Marshall® Amp Electrolytic Filter Capacitor Kits for Vintage Amps    
Top Premium Capacitor Set Shown:

Click on photo for
larger view
CAPACITOR KIT, FOR CERTAIN MARSHALL JMP, JCM800 AND SILVER JUBILEE AMP MODELS.  OR KIT, FOR CERTAIN MARSHALL  JCM800 AND JCM900 SERIES.  See specific model numbers below. Available in Top Premium (F&T/Sprague) Prime (JJ), or Pro (Tube Amp Doctor/Ruby Gold).  Fits Marshall amps which have 3 can capacitors (50uF+50uF/500V) mounted to the chassis.
JMP SERIES JCM800 SERIES SILVER JUBLIEE
1961, 1985, 1986, 1987, 1987T, 1989, 2204 1986, 1987, 2204, 2210, 4010, 4104, 4211
LATER 2203, 4103
2550, 2553, 2554, 2555, and 2558

Contains 3 50uf+50uf/500V dual can capacitors, and two axial lead EL-CAP-10/160.   Available in Top Premium, Prime, or Pro grade capacitors.

Top Premium Set:

3 F&T 50uF+50uF -500V
2 Sprague 10uF-150V


$59.95

Prime Set:

3 JJ 50uF+50uF-500V
2 Illinois 10uF-160V


$43.95

Pro Set:

3 Ruby Gold 50uF + 50uF-500V
2 OEM 10uF-160V


$31.95

Note:  This set is not for the early versions of the JCM800 2203 and 4103 from 1981-1987.

Part #MCK-1

Top Premium Set:
$59.95

Prime Set:
$43.95

Pro Set:
$31.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
CAPACITOR KIT, FOR CERTAIN MARSHALL  JCM800 AND JCM900 SERIES.  See specific model numbers below.   Available in Top Premium (F&T/Sprague), Prime (JJ), or Pro (Tube Amp Doctor/Ruby Gold).  Fits Marshall amps which have 2 can capacitors (50uF+50uF/500V) mounted to the chassis. 
JCM800 SERIES JCM900 SERIES
2205, 4210, 4212 2100, 2101, 2100SL-X, 2101SL-X, 2500, 2501, 2502, 2500SL-X, 2501SL-X, 2502SL-X, 4100, 4101, 4102, 4500, 4501, and 4502

Contains 2 50uf+50uf/500V dual can capacitors, and two axial lead EL-CAP-10/160. Available in Premium, Prime, or Pro grade capacitors.

Top Premium Set:

2 F&T 50uF+50uF -500V
2 Sprague 10uF-150V

$43.95

Prime Set:

2 JJ 50uF+50uF-500V
2 Illinois 10uF-160V


$29.95

Pro Set:

2 Ruby Gold 50uF + 50uF-500V
2 OEM 10uF-160V

$21.95


Part #MCK-2

Top Premium Set:
$43.95

Prime Set:
$29.95

Pro Set:
$21.95

 
Select Option:


Quantity:

Top Premium Capacitor Set Shown:



Click on photo for
larger view
CAPACITOR KIT, FOR CERTAIN MARSHALL 100 WATT JMP and JCM800 Models.  See specific model numbers below.

Available in Top Premium (F&T/Sprague), Prime (JJ), or Pro (Ruby Gold).  Fits Marshall amps which have 6 can capacitors (50uF+50uF/500V) mounted to the chassis. 
JMP SERIES JCM800 SERIES
1959, 1986, 1987, 1992, 2103, 2104, 2203, 2204 EARLY 2203 and 4103
1959, 1992

Contains 6 50uf+50uf/500V dual can capacitors, and two axial lead 10uF/150V.  Available in Top Premium, Prime, or Pro grade capacitors.

Top Premium Set:

6 F&T 50uF+50uF - 500V
2 Sprague 10uF-150V

$110.95

Prime Set:

6 JJ 50uF+50uF-500V
2 Illinois 10uF-160V


$89.95

Pro Set:

6 Ruby Gold
50uF + 50uF - 500V
2 OEM 10uF-160V

$63.95

Part #MCK-3

Top Premium Set:
$110.95

Prime Set:
$89.95

Pro Set:
$63.95

 
Select Option:


Quantity:

Prime Capacitor Set Shown:



Click on photo for
larger view
CAPACITOR KIT, FOR MARSHALL 9005 RACK-MOUNT POWER AMP. 

Available in Top Premium (F&T/Sprague), Prime (JJ/Ruby), or Pro (Ruby Gold).  This capacitor set replaces the electrolytic filter capacitors in both channels of the Marshall 9005 power amplifier.  Contains 4 50uf+50uf/500V dual can capacitors, two 33uF/450V axial capacitors, two 10uF/450V axial capacitors and two axial lead 10uf/160V.  Available in 3 versions:  Top Premium, Prime, or Pro grade capacitors:

Premium Set:

4 F&T 50uF+50uF-500V
2 F&T 30uF/500V
2 F&T 10uF/5000V
2 Sprague 10uF-150V


$115.95

Prime Set:

4 JJ 50uF+50uF-500V
2 Illinois 33uF/450V
2 Illinois 10uF/500V
2 Illinois 10uF-160V


$84.95

Pro Set:

4 Ruby Gold 50uF+50uF-500V
2 Illinois 33uF/450V
2 Illinois 10uF/500V
2 Axial 10uF-160V


$59.95

Part #MCK-4

Top Premium Set:
$115.95

Prime Set:
$84.95

Pro Set:
$59.95

 
Select Option:


Quantity:


Click on photo for
larger view
CAPACITOR KIT, FOR MARSHALL EARLY VERSION Lead 12 MicroStack (Model 3005) or the Lead 12 1x10 Combo (Model 5005) Contains the following filter capacitors, used as main and low voltage filters in the 3005 and 5005 Lead 12 Models.
  • 2 2200uF-25V (Main Filters)
  • 3 22uF-50V (Decoupling Filters)
  • 1 100uF-35V (Rolloff Filter)

This kit is for the early version of the Lead 12, which has only one jack next to the power switch (some didn't have a jack there at all).   See below:   

Part #MCK-5

$11.95


CAPACITOR KIT, FOR MARSHALL LATER VERSION Lead 12 MicroStack (Model 3005) or the Lead 12 1x10 Combo (Model 5005) Contains the following filter capacitors, used as main and low voltage filters in the 3005 and 5005 Lead 12 Models.
  • 2 2200uF-25V Radial (Main Filters)
  • 3 22uF-50V (Decoupling Filters)
  • 1 100uF-25V (Rolloff Filter)
  • 1 2.2uF-100V (Coupling Capacitor)

This kit is for the later version of the Lead 12, which has TWO jacks next to the power switch.   See below:   

Part #MCK-5A

$11.95


Click on photo for
larger view
CAPACITOR KIT, FOR MARSHALL® Lead 100 MOSFET (Model 3210)

Contains the following electrolytic capacitors, which includes all axial electrolytic capacitors used in the Lead 100 Mosfet Model 3210:

  • 2 2200uF-50V
  • 3 100uF-25V
  • 4 47uF-63V
  • 8 22uF-50V

Download the installation guidelines

Part #MCK-6

$29.95

 

  Music Man® Amp Electrolytic Filter Capacitor Kits for Vintage Amps    


Click on photo for
larger view
Music Man® Electrolytic Filter Capacitor Kit 1  Contains the following filter capacitors, used as main and decoupling filters, bias filters and low voltage filters in the Music Man 65 and 130 series amps.  For chassis 2275-65, 2475-65, 2275-65, and 2275-130 only.
  • 2 F&T 100uF-450V (Main Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 5 Axial 220uF-100V (Replaces 150uF-50V)

Part #MMCK-1

$43.95

  Crate® Amp Electrolytic Filter Capacitor Kit    

 

Capacitor Kit, fits Crate® Vintage Club 30 Watt and 50 Watt versions (Models VCR3112, VC5212 and VC5310) Contains all of the radial electrolytic capacitors for the Crate® Vintage Club combo amplifiers.   Contains (4) 47uF-450V, (1) 100uF-450V, (2) 1000uF-35V, (2) 47uF-50V, (7) 10uF-50V, (1) 1uF-50V, (1) 220uF-50V, and (1) 10,000uF-16V.

Part # CCK-35

$38.95

  Peavey® Amp Electrolytic Filter Capacitor Kit    

 

Capacitor Kit, fits Peavey® Original Classic 30 (mid 1990s forward)   NOT for the reissue Classic 30 II, which was introduced in 2013.   Contains all of the electrolytic capacitors for the Peavey® Classic 30 amplifier (1990s version only).   All capacitors are made by Illinois Capacitor®, all are axial type.   Contains (2) 47uF-500V, (3) 22uF-500V, (2) 2200uF-50V, (1) 100uF-25V, (9) 22uF-50V, (2) 10uF-50V, (1) 2.2uF-100V.

Part # PCK-30

$58.95

 

Capacitor Kit, fits Peavey® Delta Blues (mid 1990s forward)    Contains all of the electrolytic capacitors for the Peavey® Classic 30 amplifier (1990s version only).   All capacitors are made by Illinois Capacitor®, all are axial type.   Contains (2) 47uF-500V, (3) 22uF-500V, (2) 2200uF-50V, (1) 100uF-25V, (8) 22uF-50V, (2) 10uF-50V, (1) 2.2uF-100V, (1) 1000uF-35V.

Part # PCK-42

$58.95

 

Capacitor Kit, fits Peavey® Classic VTX Series (not the Classic VT)   Contains all of the electrolytic filter capacitors for the Peavey® Classic VTX Series amplifier (early 1980s).   All capacitors are made by Illinois Capacitor®, all are axial type.   Contains (2) 100uF-350V, (2) 22uF-50V, (2) 1000uF-35V.   Note:  Contains only the power supply filter capacitors for both high and low voltage power supplies.   Does not contain any other capacitors.

Part # PCK-81

$22.95

 

Capacitor Kit, fits Peavey® Classic VT Series (not the Classic VTX)   Contains all of the electrolytic filter capacitors for the Peavey® Classic VT Series amplifier (late 1970s).   All capacitors are made by Illinois Capacitor®, all are axial type.   Contains (4) 100uF-350V, (2) 22uF-50V, (2) 1000uF-35V, (2) 10uF-160V, (1) 10uF-500V.   Note:  Contains only the power supply filter capacitors for both high and low voltage power supplies.   Does not contain any other capacitors.

Part # PCK-82

$43.95

 

Capacitor Kit, fits Peavey® Butcher Amplifier   Contains all of the electrolytic capacitors for the Peavey® Butcher amplifier (late 1980s).   All capacitors are made by Illinois Capacitor®, all are axial type.   Contains (4) 100uF-350V, (4) 22uF-500V, (2) 220uF-100V, (1) 1000uF-50V, (1) 100uF-25V, (1) 22uF-50V.   Note:   Contains all of the electrolytic capacitors used in filtering applications.  Does not contain any other capacitors, such as non-electrolytic coupling capacitors

Part # PCK-83

$58.95

  Fender® Amp Electrolytic Filter Capacitor Kits    
Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 1.   Used in the Bassman AA864, Bandmaster AA763/AB763/AC568, Concert AA763/AB763, Pro Amp AB763, or Showman AA763/AB763/AC568.  See the complete model cross reference
Available in Top Premium (F&T
®/Sprague® Atom), Pro (Tube Amp Doctor®/Ruby Gold®), Standard OEM (Illinois Capacitor®), or Basic MOD® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
5 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$59.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
1 100uF-100V
5 TAD Gold 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$40.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
1 I.C. 47uF-63V
5 I.C. 22uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$37.95

Basic MOD® Electronics:

Our Basic MOD® Electronics Set contains Basic MOD® Capacitors, chosen for their quality and economical price:

 

3 20uF-500V
2 MOD 70uF-350V
1 MOD 100uF-100V
5 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$23.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-1

Top Premium Set:
$59.95

Pro Set:
$40.95

Standard Set:
$37.95

Basic MOD® Set:
$23.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 2.   Used in the Tremolux AA763/AB763, or Vibrolux AA763, AB763.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
1 F&T 100uF-100V
5 Sprague 25uF-50V
2 10K-2W Resistors

$68.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
1 100uF-100V
5 TAD Gold 25uF-25V
2 10K-2W Resistors

$30.95

 

Basic MOD® Electronics Set:

5 MOD 16uF-475
1 MOD 100uF-100V
5 25uF-25V
2 10K-2W Resistors

$21.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-2

Top Premium Set:
$68.95

Pro Set:
$30.95

Basic MOD® Set:
$21.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 3.   Used in the Pro Amp AA763.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 22uF-500V
1 F&T 100uF-100V
5 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$47.95

Pro Set:

5 TAD Gold 22uF-500V
1 100uF-100V
5 TAD Gold 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor

$33.95

Standard (OEM) Set:

5 I.C. 22uF-500V
1 I.C. 47uF-63V
5 I.C. 22uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$29.95

Basic MOD® Electronics:

Our Basic MOD® Electronics Set contains Basic MOD® Capacitors, chosen for their quality and economical price:

 

5 20uF-500V
1 MOD 100uF-100V
5 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor

 

$22.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-3

Top Premium Set:
$47.95

Pro Set:
$33.95

Standard Set:
$29.95

Basic MOD® Set:
$22.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 4.   Used in the Bandmaster Reverb AA768, Pro Reverb AA165, Showman Reverb AA768, Super Reverb AB763/AB568, Twin Reverb AB763, or Vibroverb AB763.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$66.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
1 100uF-100V
7 TAD Gold 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
1 I.C. 100uF-100V
7 I.C. 22uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$39.95

Basic MOD® Electronics:

Our Basic MOD® Electronics Set contains Basic MOD® Capacitors, chosen for their quality and economical price:

 

3 20uF-500V
2 MOD 70uF-350V
1 MOD 100uF-100V
7 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$24.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-4

Top Premium Set:
$66.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic MOD® Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 4A.   Used in the Twin Reverb AC568 or AA769.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor
2 220K-1W Resistors

$66.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
1 100uF-100V
7 TAD Gold 25uF-25V
1 10K-2W Resistor
1 2.2K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
1 I.C. 100uF-100V
7 I.C. 22uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor
2 220K-1W Resistors

$39.95

Basic MOD® Electronics:

Our Basic MOD® Electronics Set contains Basic MOD® Capacitors, chosen for their quality and economical price:

 

3 MOD 20uF-500V
2 MOD 70uF-350V
1 MOD 100uF-100V
7 MOD 25uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor
2 220K-1W Resistors

$24.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-4A

Top Premium Set:
$66.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic MOD Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 4B.   Used in the Bandmaster Reverb AA1069, Dual Showman Reverb AA769, Pro Reverb AA1069, Pro Reverb AA270, or Super Reverb AA1069.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various selected brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$66.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
1 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
1 I.C. 100uF-100V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$39.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 80uF-500V
1 70uF-100V
6 25uF-25V
1 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$24.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-4B

Top Premium Set:
$66.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic Economy Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 4C.   Used in the Pro Reverb AB668.  See the complete model cross reference
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various selected brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$66.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
1 100uF-100V
7 TAD Gold 25uF-25V
1 10K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
1 I.C. 47uF-63V
7 I.C. 22uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$39.95

Basic MOD® Electronics:

Our Basic MOD® Electronics Set contains Basic MOD® Capacitors, chosen for their quality and economical price:

 

3 MOD 20uF-500V
2 MOD 70uF-350V
1 MOD 100uF-100V
7 MOD 25uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$24.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-4C

Top Premium Set:
$66.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic MOD Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 5.   Used in the Super Reverb AA763 or Vibroverb AA763.  See the complete model cross reference.
Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various selected brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 22uF-500V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$54.95

Pro Set:

5 TAD Gold 22uF-500V
1 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$32.95

Standard (OEM) Set:

5 I.C. 22uF-500V
1 I.C. 47uF-63V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$29.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

5 20uF-500V
1 70uF-100V
6 25uF-25V
1 4.7uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor

$23.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-5

Top Premium Set:
$54.95

Pro Set:
$32.95

Standard Set:
$29.95

Basic Economy Set:
$23.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 6.   Used in the Deluxe Reverb AA763/AB763/AB868 or Vibrolux Reverb AA964.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
1 F&T 100uF-100V
7 Sprague 25uF-50V
2 10K-2W Resistors

$74.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
1 100uF-100V
7 TAD Gold 25uF-25V
2 10K-2W Resistors

$33.95

 

Basic MOD Set:

5 MOD 16uF-475
1 MOD 100uF-100V
7 MOD 25uF-50V
2 10K-2W Resistors

$24.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-6

Top Premium Set:
$74.95

Pro Set:
$33.95

Basic MOD Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 6A.   Used in the Vibrolux Reverb AB568.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), or Basic MOD
® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor

$74.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
1 100uF-100V
7 TAD Gold 25uF-25V
1 10K-2W Resistor
1 4.7K-2W Resistor

$33.95

 

Basic MOD Set:

5 MOD 16uF-475
1 MOD 100uF-100V
7 25uF-25V
1 10K-2W Resistor
1 4.7K-2W Resistor

$24.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-6A

Top Premium Set:
$74.95

Pro Set:
$33.95

Basic MOD Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 6B.   Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), or Basic MOD® Electronics (MOD® Capacitors).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors in the Fender Deluxe Amp AB763:

Top Premium Set:

4 F&T 16uF-475V
1 F&T 100uF-100V
5 Sprague 25uF-50V
1 10K-2W Resistor
1 27K-2W Resistor

$59.95
Free USA shipping
on this kit!

Pro Set:

4 TAD Gold 16uF-475
1 100uF-100V
5 TAD Gold 25uF-25V
1 10K-2W Resistor
1 27K-2W Resistor

$25.95

 

Basic MOD Set:

4 MOD 16uF-475
1 MOD 100uF-100V
5 MOD 25uF-50V
1 10K-2W Resistor
1 27K-2W Resistor

$19.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-6B

Top Premium Set:
$59.95

Pro Set:
$25.95

Basic MOD Set:
$19.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 7.   Used in the Bandmaster Reverb AA270, Bandmaster Reverb w/Master Volume 45 Watt Output (1972-1974), Pro Reverb w/Master Volume 45 Watt Output (1973-1974), Super Reverb AA270, Super Reverb w/Master Volume 45 Watt Output (1972-1974), or Super Six Reverb without Master Volume (1971).  See the complete model cross reference.  NOTE:  Extra resistors are included in this kit to accommodate differences in different model builds.   You will not need all of the resistors.   In some models, you may have one cathode bypass capacitor left over.  Available in Top Premium (F&T/Sprague Atom), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various selected brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$69.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
2 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$40.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 80uF-500V
2 100uF-100V
6 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 220K-1W Resistors

$27.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-7

Top Premium Set:
$69.95

Pro Set:
$43.95

Standard Set:
$40.95

Basic Economy Set:
$27.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 8.   Used in the Deluxe Reverb A1172 or A1270, or the Deluxe Reverb "Volume Boost Model" (late 1970`s).  See the complete model cross reference.  Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold) or Basic Economy (various selected brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
1 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$75.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
1 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$40.95

 

Basic Economy Set:

5 16uF-475
1 100uF-100V
6 25uF-25V
1 4.7uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$21.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-8

Top Premium Set:
$75.95

Pro Set:
$40.95

Basic Economy Set:
$21.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 8A.   Used in some versions of the Vibrolux Reverb (1977-1982) with a Pull-Boost Switch on the Volume Control.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold)or Basic Economy (various selected brands). 

*Before ordering, slide out the amp chassis and remove the capacitor cover under the chassis.   If your amp has five 16uF/450 capacitors, this FCK-8A is the kit you need.  Otherwise, look at kit FCK-8B, below.

Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
2 F&T 100uF-100V
5 Sprague 25uF-50V
1 Sprague 5uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$77.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
2 100uF-100V
5 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$41.95

 

Basic Economy Set:

5 16uF-475
2 100uF-100V
5 25uF-25V
1 4.7uF-50V
1 10K-2W Resistor
1 2.2K-2W Resistor

$22.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-8A

Top Premium Set:
$77.95

Pro Set:
$41.95

Basic Economy Set:
$22.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 8B.   Used in some versions of the Vibrolux Reverb (1977-1982) with a Pull-Boost Switch on the Volume Control.  See the complete model cross reference

Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold)or Basic Economy (various selected brands).
*Before ordering, slide out the amp chassis and remove the capacitor cover under the chassis.   If your amp has two 60uF/450V capacitors and three 16uF/450 capacitors, this FCK-8B is the kit you need.  Otherwise, look at kit FCK-8A, above.
Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 16uF-475V
2 F&T 80uF-450V
2 F&T 100uF-100V
5 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$79.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 16uF-475
2 TAD Gold 80uF-450V 
2 100uF-100V
5 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$43.95

Basic Economy Set:

3 16uF-475
2 80uF-500V
2 100uF-100V
5 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$26.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-8B

Top Premium Set:
$79.95

Pro Set:
$43.95

Basic Economy Set:
$26.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 8C.   Used in the Vibrolux Reverb AA270 (1970-1976).  See the complete model cross reference.  Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold) or Basic MOD® Electronics (MOD® Capacitors).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

5 F&T 16uF-475V
1 F&T 100uF-100V
7 Sprague 25uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor

$75.95
Free USA shipping
on this kit!

Pro Set:

5 TAD Gold 16uF-475
1 100uF-100V
7 TAD Gold 25uF-25V
1 10K-2W Resistor
1 4.7K-2W Resistor

$40.95

 

Basic MOD Set:

5 MOD 16uF-475
1 MOD 100uF-100V
7 MOD 25uF-50V
1 10K-2W Resistor
1 4.7K-2W Resistor

$24.95

 

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-8C

Top Premium Set:
$75.95

Pro Set:
$40.95

Basic MOD Set:
$24.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 9.   Used in silverface Dual Showman, Quad, Super Six, Twin and Vibrosonic Reverb amps from 1971-1972 which have a master volume control, but DO NOT have the push/pull switch for boost on the master volume.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor).      Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$69.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
2 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$45.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$41.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 80uF-500V
2 100uF-100V
6 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$27.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-9

Top Premium Set:
$69.95

Pro Set:
$45.95

Standard Set:
$41.95

Basic Economy Set:
$27.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 9A.   Used in the following Dual Showman Reverb, Quad Reverb, Super Six Reverb, Twin Reverb, and Vibrosonic Reverb models:  (1972-1974)  Equipped w/Master Volume & Push/Pull Switch, 100 Watt.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 100uF-350V
2 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$69.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 Ruby Gold 100uF-350V
2 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$45.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 100uF-350V
2 I.C. 100uF-100V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$41.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 100uF-350V
2 100uF-100V
6 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$27.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-9A

Top Premium Set:
$69.95

Pro Set:
$45.95

Standard Set:
$41.95

Basic Economy Set:
$27.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 10.   Used in the Fender Ultralinear Models from 1974-1980 as follows:  Bandmaster Reverb 70 Watts, Dual Showman 135 Watts, Pro Reverb 70 Watts, Quad Reverb 135 Watts, Super Reverb 70 Watts, Super Six Reverb 135 Watts, Twin Reverb 135 Watts, or Vibrosonic Reverb 135 Watts.   Wattage on these models is printed near the speaker out jack.   See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
5 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$71.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 220uF-350V
2 100uF-100V
5 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$49.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
5 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$45.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 220uF-350V
2 100uF-100V
5 25uF-25V
1 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$31.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-10

Top Premium Set:
$71.95

Pro Set:
$49.95

Standard Set:
$45.95

Basic Economy Set:
$31.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 10A.   Used in the Fender PA-135 (1976-1979).  See the complete model cross reference.  Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands). This kit contains filter capacitors - no cathode bypass capacitors are included.  Contains the following capacitors, used as main filters and bias filter capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$61.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 220uF-350V
2 100uF-100V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$45.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$41.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 220uF-350V
2 100uF-100V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$29.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-10A

Top Premium Set:
$61.95

Pro Set:
$45.95

Standard Set:
$41.95

Basic Economy Set:
$29.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 11.   Used in the Bassman AA270.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
1 F&T 10uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
5 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$72.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
1 TAD Gold 8uF-475V
2 TAD Gold 80uF-450V 
2 100uF-100V
5 TAD Gold 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$48.95

Standard (OEM) Set:

3 I.C. 22uF-500V
1 I.C. 10uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
5 I.C. 22uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$44.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
1 10uF-500V
2 80uF-500V
2 70uF-100V
5 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$34.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-11

Top Premium Set:
$72.95

Pro Set:
$48.95

Standard Set:
$44.95

Basic Economy Set:
$34.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 11A.   Used in the Bassman AA371, or Bassman 50 Combo (1972-1976).  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
1 F&T 10uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
3 Sprague 25uF-50V
1 Sprague 5uF-50V
1 I.C. 1uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$70.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
1 TAD Gold 8uF-475V
2 TAD Gold 80uF-450V 
2 100uF-100V
3 TAD Gold 25uF-25V
1 4.7uF-50V
1 1uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$48.95

Standard (OEM) Set:

3 I.C. 22uF-500V
1 I.C. 10uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
3 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 I.C. 1uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$43.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
1 10uF-500V
2 80uF-500V
2 70uF-100V
3 25uF-25V
1 4.7uF-50V
1 1uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$33.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-11A

Top Premium Set:
$70.95

Pro Set:
$48.95

Standard Set:
$43.95

Basic Economy Set:
$33.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 12.   Used in the Dual Showman Reverb AA270 or Twin Reverb AA270.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
6 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$69.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
2 100uF-100V
6 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$44.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
6 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$40.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 80uF-500V
2 70uF-100V
6 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$27.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-12

Top Premium Set:
$69.95

Pro Set:
$44.95

Standard Set:
$40.95

Basic Economy Set:
$27.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 13.   Used in the Bassman Ten Combo (50 watts, 1972-1976), Bantam Bass, and Super Bassman.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 80uF-450V
2 F&T 100uF-100V
2 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$57.95

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 80uF-450V 
2 100uF-100V
2 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 80uF-450V
2 I.C. 100uF-100V
2 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$39.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 80uF-500V
2 70uF-100V
2 25uF-25V
1 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$26.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-13

Top Premium Set:
$57.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic Economy Set:
$26.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 13A.   Used in the Bassman 100 head (1972-1976).  See the complete model cross reference.  Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 100uF-350V
2 F&T 100uF-100V
1 Sprague 25uF-50V
2 Sprague 5uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$57.95

Pro Set:

3 TAD Gold 22uF-500V
2 Ruby Gold 100uF-350V
2 100uF-100V
1 TAD Gold 25uF-25V
2 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$43.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 100uF-350V
2 I.C. 100uF-100V
1 I.C. 22uF-50V
2 I.C. 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$39.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 100uF-350V
2 100uF-100V
1 25uF-25V
2 4.7uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$26.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-13A

Top Premium Set:
$57.95

Pro Set:
$43.95

Standard Set:
$39.95

Basic Economy Set:
$26.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 13B.   Used in the Bassman 135 head (1977-1983).  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
1 Sprague 25uF-50V
2 Sprague 5uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$59.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 220uF-300V
2 100uF-100V
1 TAD Gold 25uF-25V
2 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$45.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
1 I.C. 22uF-50V
2 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$41.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 220uF-350V
2 100uF-100V
1 25uF-25V
2 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$29.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-13B

Top Premium Set:
$59.95

Pro Set:
$45.95

Standard Set:
$41.95

Basic Economy Set:
$29.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 13C.   Used in the Bassman 70 Head (1977-1983).  See the complete model cross reference.    Note about this amp:    The Bassman 70 used a 750uF/3V cathode capacitor in the first stage of the bass channel.   This value of capacitor is no longer available from any sources.   A 25uF capacitor is included in the kit to use as a replacement.  Or the original 750uF/3V capacitor may be left in place as another option.
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
4 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$65.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 220uF-300V
2 100uF-100V
4 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$49.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
4 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$43.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 220uF-350V
2 100uF-100V
4 25uF-25V
1 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$31.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-13C

Top Premium Set:
$65.95

Pro Set:
$49.95

Standard Set:
$43.95

Basic Economy Set:
$31.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 13D.   Used in the Bassman Ten Combo (75 Watts, 1977-1982).  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
2 Sprague 25uF-50V
1 Sprague 5uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$58.95

Pro Set:

3 TAD Gold 22uF-500V
2 TAD Gold 220uF-300V
2 100uF-100V
2 TAD Gold 25uF-25V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$46.95

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
2 I.C. 22uF-50V
1 I.C. 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$41.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 220uF-350V
2 100uF-100V
2 25uF-25V
1 4.7uF-50V
1 2.7K-10W Resistor
1 1K-2W Resistor
1 4.7K-2W Resistor
2 100K-1W Resistors

$29.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-13D

Top Premium Set:
$58.95

Pro Set:
$46.95

Standard Set:
$41.95

Basic Economy Set:
$29.95

Select Option:


Quantity:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 14.  Contains the following capacitors, used as main filters and preamp cathode bypass capacitors in the Fender blackface and silverface Champ (1964-1982).    Does NOT include any of the many Champ "variation" models - just the basic Champ Amp.  See the complete model cross reference


  • 1 CE Mfg 20uFX4-475V (Main Filters - Decoupling)
  • 2 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 2.2uF-100V (Cathode Bypass)
  • 470-2W Resistor (Cathode Resistor)
  • 1K-2W Resistor (Dropping Resistor)
  • 10K-2W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-14

$52.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 15.  Contains the following capacitors, used as main filters and preamp cathode bypass capacitors in the Fender blackface Princeton Amp (without reverb) AA964 from 1964-1967 and the Fender silverface Princeton (without reverb) AA964/AB1270 from 1968-1979.   Does NOT include any of the many Princeton "variation" models - just the basic Princeton without reverb.  See the complete model cross reference.  Available in Top Premium or Standard Sets.


Click on photos for larger view

Top Premium Set:

1 CE Mfg 20uFX4-475V
3 Sprague 25uF-50V
1 F&T 100uF-100V
1 1K-2 Watt Resistor
2 18K-2 Watt Resistors

$73.95

Standard Set:

1 CE Mfg 20uFX4-475V
3 Generic 25uF-25V
1 Generic 100uF-100V
1 1K-2 Watt Resistor
2 18K-2 Watt Resistors

$60.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-15

Top Premium Set:
$73.95

Standard Set:
$60.95
 

Select Option:


Quantity:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 16.  Contains the following capacitors, used as main filters and preamp cathode bypass capacitors in the Fender blackface Princeton Reverb amp from 1964-1970 and the silverface Princeton Reverb Amp AB1270 from 1970-1981.   Does NOT include any of the many Princeton "variation" models - just the basic silverface Princeton Reverb Amp AA764 or AA1164 and the AB1270 with reverb.   Does NOT include the reissue models.  See the complete model cross reference



Click on photos for larger view

Top Premium Set:

1 CE Mfg 20uFX4-475V
6 Sprague 25uF-50V
1 F&T 100uF-100V
1 1K-2 Watt Resistor
2 18K-2 Watt Resistors

$83.95

Standard Set:

1 CE Mfg 20uFX4-475V
6 Generic 25uF-25V
1 Generic 100uF-100V
1 1K-2 Watt Resistor
2 18K-2 Watt Resistors

$63.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-16

Top Premium Set:
$83.95

Standard Set:
$63.95
  

Select Option:


Quantity:



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 17.  Contains the following capacitors, used as main filters, decoupling filters, bias filters and low voltage filters in the Fender Pro Tube amps.    This includes the Pro Reverb PR448, the Concert Reverb PR450 and the Twin Amp PR449 from 2001-2005.   These amps are easy to spot, because they have only one input jack on the far left side of the front control panel.  See the complete model cross reference

  • 4 F&T 47-500 (Main Filters - Replaces 47uF/350)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 100uF/100V (Bias Filters)
  • 2 Radial 220uF/50V (Low Voltage Filters)
  • 2 Radial 1000uF/35V (Low Voltage Filters)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-17

$58.95

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 18.   Used in the Bassman AA165, AB165, AC568.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various selected brands).  Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

3 F&T 22uF-500V
1 F&T 10uF-500V
2 F&T 80uF-450V
1 F&T 100uF-100V
5 Sprague 25uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$67.95
Free USA shipping
on this kit!

Pro Set:

3 TAD Gold 22uF-500V
1 TAD Gold 8uF-475V
2 TAD Gold 80uF-450V 
1 100uF-100V
5 TAD Gold 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$48.95

Standard (OEM) Set:

3 I.C. 22uF-500V
1 I.C. 10uF-500V
2 I.C. 80uF-450V
1 I.C. 100uF-100V
5 I.C. 22uF-50V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$42.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
1 10uF-450V
2 80uF-500V
1 70uF-100V
5 25uF-25V
1 1K-2W Resistor
1 4.7K-2W Resistor
1 27K-2W Resistor
2 220K-1W Resistors

$32.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-18

Top Premium Set:
$67.95

Pro Set:
$48.95

Standard Set:
$42.95

Basic Economy Set:
$32.95

Select Option:


Quantity:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 19.  Used in the Super Twin and Super Twin Reverb (180 Watts 1975-1976).  See the complete model cross reference

Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

  • 3 F&T 22uF-500V (Main Filters - Decoupling)
  • 2 F&T 220uF-300V (Main Filters)
  • 2 F&T 100uF-100V (Bias Filters)
  • 2 Axial 4.7uF-450V (Decoupling)
  • 3 25uF-25V (Cathode Bypass)
  • 2 4.7uF-50V (Cathode Bypass)

NOTES:   Does not include the 750uF/3V or 150uF/6V cathode bypass capacitors.   Some Super Twin models (without reverb) will not use all of the cathode bypass capacitors provided.

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-19

$58.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 20.  Contains the following capacitors, used as main filters and preamp cathode bypass capacitors in the Fender blackface and silverface Vibro Champ (1967-1975) and Bronco Amp (1964-1975).    Does NOT include the Paul Rivera blackface VibroChamp from 1981-1982, the Vibro Champ XD (2007-2012) nor the Eric Clapton Vibro Champ (2011-2013).  See the complete model cross reference



  • 1 CE Mfg 20uFX4-475V (Main Filters - Decoupling)
  • 3 25uF-25V (Cathode Bypass)
  • 1 10uF-50v (Cathode Bypass)
  • 1K-2W Resistor (Dropping Resistor)
  • 10K-2W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-20

$52.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 21.  Contains the following capacitors, used as main filters, decoupling filters, bias filters, low voltage filters and cathode bypass capacitors in the Fender 94 Twin Amp, Rev A-C.  (If your 94 Twin has a Rev D or Rev E circuit board, you will need the FCK-21D kit).  The 94 Twin Amp is blackface, is "three channel" with a boost on the clean channel and high gain overdrive on channel two.   Two input jacks, 14 knobs.  Revisions A, B and C produced 1994-1998.  See the complete model cross reference

Click on photo for larger view

  • 2 F&T 220uF-300V (Main Filters)
  • 4 F&T 47uF-500V (Decoupling Filters)
  • 4 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 100uF-100V (Bias Filters)
  • 4 Radial 22uF-63V (Bias and Relay Filters)
  • 7 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 4.7uF-50V (Cathode Bypass)
  • 2 Radial 220uF-50V (Low Voltage Filter)
  • 2 Radial 1000uF-35V (Low Voltage Filter)
  • 1 Radial 47uF-50V (Relay Filter)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-21

$89.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 21D.  Contains the following capacitors, used as main filters, decoupling filters, bias filters, low voltage filters and cathode bypass capacitors in the Fender 94 Twin Amp, Rev D and Rev E.  (If your 94 Twin has a Rev A through Rev C circuit board, you will need the FCK-21 kit).  The 94 Twin Amp is blackface, is "three channel" with a boost on the clean channel and high gain overdrive on channel two.   Two input jacks, 14 knobs.  Revisions D and E produced 1999-2001.  See the complete model cross reference

Click on photo for larger view

  • 2 F&T 220uF-300V (Main Filters)
  • 2 F&T 47uF-500V (Decoupling Filters)
  • 5 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 100uF-100V (Bias Filters)
  • 4 Radial 22uF-63V (Bias and Relay Filters)
  • 7 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 4.7uF-50V (Cathode Bypass)
  • 2 Radial 220uF-50V (Low Voltage Filter)
  • 2 Radial 1000uF-35V (Low Voltage Filter)
  • 1 Radial 47uF-50V (Relay Filter)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-21D

$76.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 22.  Contains the following capacitors, used as main filters, decoupling filters, bias filters, cathode bypass capacitors in the Fender `65 Princeton Reverb Reissue amp, produced from 2008 to the present.  See the complete model cross reference

  • 4 F&T 22uF-500V (Main and Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filters)
  • 6 25uF-25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-22

$27.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 23.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Deluxe Reverb Reissue amp, produced from 1993 to the present, and the `68 Custom Deluxe Reverb amp, produced from 2007 to the present.  See the complete model cross reference

  • 1 F&T 47uF-500V (Main Filter)
  • 1 Axial 220uF-100V (Main Filter)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-63V (Bias Filter)
  • 7 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 4.7uF-50V (Footswitch Suppression)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-23

$35.95



Click on photo for
larger view

Fender® Electrolytic Standard OEM Filter Capacitor Kit 24.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Super Reverb Reissue amp, produced from 2000 to the present. 

  • 2 I.C. 100uF-350V (Main Filters)
  • 3 I.C. 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-50V (Cathode Bypass)
  • 6 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 4.7uF-50V (Footswitch Suppression)

Part #FCK-24 (See also FCK-24A, below)

$33.95



Click on photo for
larger view

Fender® Top Premium Electrolytic Filter Capacitor Kit 24A.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Super Reverb Reissue amp, produced from 2000 to the present. 

  • 2 F&T 100uF-350V (Main Filters)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-50V (Cathode Bypass)
  • 6 Sprague 25uF-50V (Cathode Bypass)
  • 1 Sprague 5uF-50V (Footswitch Suppression)

Part #FCK-24A

$68.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 25.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Twin Reverb Reissue amp, produced from 1991 to the present and the Fender `68 Custom Twin Reverb amp, produced from 2009 to the present. 

  • 2 F&T 220uF-300V (Main Filters)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-63V (Bias Filter)
  • 1 Radial 10uF-100V (Footswitch Filter)
  • 7 Radial 22uF-50V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-25

$45.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 26.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, and cathode bypass capacitors in the Fender Custom Vibrolux Reverb amp from 1995-2010.   Note:  This is the blackface Custom Vibrolux Reverb Reissue amp with white "cupcake" knobs and the control levels printed on the front panel.  We do not currently have a recap kit for the 68 Custom Vibrolux Reverb amp that is silverface with a drip edge.  See the complete model cross reference

  • 5 F&T 22uF-500V (Main & Decoupling Filters)
  • 1 F&T 47uF-500V (Decoupling Filter)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-63V (Bias Filter)
  • 6 25uF-25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-26

$44.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 27.  Contains the following capacitors, used as main filters, decoupling filters, bias filters, and cathode bypass capacitors in the Fender `59 Bassman Reissue amp from 1990 to the present.   See the complete model cross reference

  • 2 F&T 100uF-350V (Main Filters)
  • 2 F&T 47uF-500V (Main Filters)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 10uF-100V (Bias Filters)
  • 1 Radial 220uF-25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-27

$56.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 28.  Contains the following capacitors, used as main filters, decoupling filters, and cathode bypass capacitors in the Fender 63 Reverb (Reissue Series Reverb Unit) from 1994 to 2016.  See the complete model cross reference

  • 2 F&T 22uF-500V (Main and Decoupling Filters)
  • 1 F&T 47uF-500V (Decoupling Filter)
  • 2 I.C. 22uF-50V (Cathode Bypass Filters)
  • 1 Axial 220uF-16V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-28

$23.95


Click on photo for
larger view

Capacitor Kit, for the original Fender® 6G15 Reverb Unit (1961-1966)  Contains all of the axial electrolytic capacitors for the Fender® original tube Reverb Unit from the 1960s.   Contains three Illinois Capacitor 47uF-500V (replaces 40uF-450V), two 25uF-25V, and one 220uF-16V (replaces 250uF-6V), along with a 10K 2 watt dropping resistor.

Part # FCK-28A

$25.95



Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 29.  Contains the following capacitors, used as main filters, decoupling filters, and cathode bypass capacitors in the Fender 93 Concert Amp (PR245) from 1993 to 1995.  (Not for the vintage Concert Amps from the 1960s.  Not for the Concert II amps from 1982-1987.  Not for the Concert Reverb Amp PR450 from 2001-2004).  See the complete model cross reference

  • 3 F&T 22uF-500V (Main and Decoupling Filters)
  • 4 F&T 100uF-350V (Main Filters)
  • 9 I.C. 22uF-50V (Cathode Bypass Filters - Replaces 22uf/16V)
  • 1 I.C. 2.2uF-100V (Replaces 2.2uF/50V)
  • 1 IC. 4.7uF-50V
  • 3 Radial 22uF/63V
  • 2 Radial 100uF/100V
  • 1 Radial 220uF/25V
  • 2 Radial 220uF/50V
  • 2 Radial 1000uF/35V

See the model cross reference for applicable models. 

Part #FCK-29

$72.95

Pro Capacitor Set Shown:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 30.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Deluxe 6G3 (Brownface) from 1961-1963.  Available in Top Premium or Pro versions.  See the complete model cross reference

Top Premium Set:

3 F&T 16uF-475
1 F&T 10uF-500V
1 F&T 100uF-100V
3 Sprague 25uF-50V
1 1K-2W Resistor
1 10K-2W Resistor
1 27K-2W Resistor

$53.95

Pro Set:

3 TAD Gold 16uF-475
1 TAD Gold 8uF-475V
1 100uF-100V
3 TAD Gold 25uF-25V
1 1K-2W Resistor
1 10K-2W Resistor
1 27K-2W Resistor

$21.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-30

Top Premium Set:
$53.95

Pro Set:
$21.95
 

Select Option:


Quantity:

Pro Capacitor Set Shown:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 31.  Contains the following filter capacitors, used as main and decoupling filters, and cathode bypass capacitors in the Fender® Harvard 6G10 (Tweed) from 1961-1962.  Available in Top Premium or Pro versions.  See the complete model cross reference

Top Premium Set:

2 F&T 16uF-475
2 F&T 10uF-450V
2 Sprague 25uF-50V
1 10K-2W Resistor
1 22K-1/2W Resistor

$45.95

Pro Set:

2 TAD Gold 16uF-475
2 TAD Gold 8uF-475V
2 TAD Gold 25uF-25V
1 10K-2W Resistor
1 22K-1/2W Resistor

$19.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-31

Top Premium Set:
$45.95

Pro Set:
$19.95
  

Select Option:


Quantity:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 32.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Tremolux 6G9 (Blonde) from 1961.    For the Tremolux 6G9A and 6G9B from 1962-1963, see the FCK-33 kit.  See the complete model cross reference
  • 5 TAD Gold 16uF-475 (Main and Decoupling Filters)
  • 2 IC 10uF-50V (Bias Filters)
  • 4 25uF-25V (Cathode Bypass)
  • 2 10K-2W Resistor (Dropping Resistors)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-32

$27.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 33.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Tremolux 6G9A and 6G9B (Blonde) from 1962-1963, and Fender Vibrolux 6G11 and 6G11A (Brownface) from 1961-1963.    For the Tremolux 6G9 from 1961, see the FCK-32 kit.  See the complete model cross reference
  • 5 TAD Gold 16uF-475 (Main and Decoupling Filters)
  • 1 100uF-100V (Bias Filter)
  • 4 TAD Gold 25uF-25V (Cathode Bypass)
  • 2 10K-2W Resistor (Dropping Resistors)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-33

$29.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 34.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Bandmaster 6G7 (Brownface 3x10 combo, 1960), Concert 6G12 (Brownface combo, 1960), Pro 6G5 (Brownface combo, 1960-1961), Showman 6G14 (Blonde piggyback, 1960-1961), Super 6G4 (Brownface combo, 1960-1961), and Twin 6G8A (Blonde combo, 1962-1963).   NOTE:  Extra dropping resistors are included in this kit in order to match possible variance in models.   Use the resistors from the kit which match the original resistors in the amp.  See the complete model cross reference.   
  • 7 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 4 25uF-25V (Cathode Bypass)
  • 1 2.2uF-100V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 3 27K-2W Resistors (Dropping Resistors)
  • 3 56K-1W Resistors (Dropping Resistors)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-34

$39.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 35.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Bandmaster 6G7A* (Blonde piggyback, 1961-1963), Concert 6G12A* (Brownface combo, 1961-1963), Showman 6G14A (Blonde piggyback, 1960-1961), Super 6G4A* (Brownface combo, 1962-1963), and Vibrosonic 6G13A* (Brownface combo, 1961-1963).  See the complete model cross reference

*Note:  Some versions of these models built in late 1963 use the FCK-36 instead.  It is a good idea to open the amp and compare capacitor values to the kit contents to ensure you get the correct kit.

  • 7 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 4 25uF-25V (Cathode Bypass)
  • 1 4.7uF-50V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 3 27K-2W Resistors (Dropping Resistors)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-35

$39.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 36.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Pro 6G5A (Brownface combo, 1962-1963).  See the complete model cross reference
  • 7 22uF-560V (Main and Decoupling Filters)
  • 1 50uF-50V (Bias Filter)
  • 4 25uF-25V (Cathode Bypass)
  • 1 2.2uF-100V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 3 27K-2W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-36

$38.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 37.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Showman 6G14 (Blonde piggyback, 1960-1961).  See the complete model cross reference
  • 7 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 2 25uF-25V (Cathode Bypass)
  • 2 50uF-50V (Cathode Bypass)  Replaces 50uF-25V
  • 1 4.7uF-50V (Cathode Bypass)  Replaces 4uF-25V
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 2 27K-2W Resistor (Dropping Resistor)
  • 1 56K-1W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-37

$39.95



Click on photo for
larger view
>
Fender® Electrolytic Filter Capacitor Kit 38.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Twin 6G8 (Blonde combo, 1961).  See the complete model cross reference
  • 7 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 2 25uF-25V (Cathode Bypass)
  • 2 50uF-50V (Cathode Bypass)   Replaces 50uF-25V
  • 1 4.7uF-50V (Cathode Bypass)  Replaces 4uF-25V
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 2 27K-2W Resistor (Dropping Resistor)
  • 1 56K-1W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-38

$39.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 39.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Vibroverb 6G16 (Brownface combo, 1963).  See the complete model cross reference
  • 5 TAD Gold 16uF-475 (Main and Decoupling Filters)
  • 1 100uF-100V (Bias Filter)
  • 6 TAD Gold 25uF-25V (Cathode Bypass)
  • 2 10K-2W Resistor (Dropping Resistors)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-39

$32.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Bassman 6G6 (Blonde piggyback, 1961-1963).  See the complete model cross reference
  • 6 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 3 25uF-25V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 1 27K-2W Resistor (Dropping Resistor)
  • 1 56K-1W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-40

$33.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 41.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Bassman 6G6A (Blonde piggyback, 1962-1963).  See the complete model cross reference
  • 6 22uF-560V (Main and Decoupling Filters)
  • 2 8uF-150V (Bias Filters)
  • 4 25uF-25V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 1 27K-2W Resistor (Dropping Resistor)
  • 1 56K-1W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-41

$34.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 42.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Bassman 6G6B (Blonde piggyback, 1963-1964).  See the complete model cross reference
  • 6 22uF-560V (Main and Decoupling Filters)
  • 1 70uF-100V (Bias Filter)
  • 4 25uF-25V (Cathode Bypass)
  • 1 4.7K-2W Resistor (Dropping Resistor)
  • 1 27K-2W Resistor (Dropping Resistor)
  • 1 56K-1W Resistor (Dropping Resistor)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-42

$34.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 44.  Contains the following filter capacitors, used as main and decoupling filters and power tube cathode bypass filter in the Fender® Pawn Shop Excelsior (2012-2015).  Does not include the preamp section cathode bypass capacitors.  See the complete model cross reference
  • 4 F&T 22uF-500V (Main and Decoupling Filters)
  • 1 F&T 100uF-100V (Output Cathode Bypass Filter)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-44

$28.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 45.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Princeton 6G2 (1963-1964).  See the complete model cross reference
  • 1 CE Mfg 30uFX3-525V (Main Filters - Decoupling)
  • 1 25uF-50V (Bias Filter)
  • 2 25uF-25v (Cathode Bypass)
  • 1K-2W Resistor (Dropping Resistor)
  • 10K-2W Resistor (Dropping Resistor)

Part #FCK-45

See the model cross reference for applicable models.  Download the installation guidelines.

$52.95

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 50.   Available in Top Premium (F&T/IC), or Standard (IC).   Used in some early versions of the Vibro King Amp from 1994 to 1997.  See the complete model cross reference.   *This kit is designed for Vibro King amps which use an EL84 or 6BQ5 tube as the reverb driver tube.  Before ordering, check the tubes in the amp.    If you find an EL84 or 6BQ5, this is the correct kit for your version of the Vibro King.  If the reverb driver tube is a 6V6, see the FCK-50A kit.  Contains the following capacitors, used as main filters, bias filter, and cathode bypass capacitors:

Top Premium Set:

6 F&T 22uF-500V
2 F&T 220uF-300V
2 F&T 100uF-100V
4 I.C. 22uF-50V
2 Radial 10uF-100V

$64.95
Free USA shipping
on this kit!

Standard Set:

6 I.C. 22uF-500V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
4 I.C. 22uF-50V
2 Radial 10uF-100V

$56.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-50

Top Premium Set:
$64.95

Standard Set:
$56.95

Select Option:


Quantity:

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 50A.   Available in Top Premium (F&T/IC), or Standard (IC).   Used in some early versions of the Vibro King Amp from 1994 to 1997.  See the complete model cross reference.   *This kit is designed for Vibro King amps which use a 6V6 tube as the reverb driver tube.  Before ordering, check the tubes in the amp.    If you find a 6V6, this is the correct kit for your version of the Vibro King.  If the reverb driver tube is an EL84 or 6BQ5, see the FCK-50 kit.  Contains the following capacitors, used as main filters, bias filter, and cathode bypass capacitors:

Top Premium Set:

3 F&T 47uF-500V
2 F&T 220uF-300V
1 F&T 100uF-350V
3 F&T 100uF-100V
3 I.C. 22uF-50V
1 I.C. 2.2uF-100V
2 Radial 10uF-100V

$64.95
Free USA shipping
on this kit!

Standard Set:

3 I.C. 47uF-500V
2 I.C. 220uF-300V
1 I.C. 100uF-350V
3 I.C. 100uF-100V
3 I.C. 22uF-50V
1 I.C. 2.2uF-100V
2 Radial 10uF-100V

$56.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-50A

Top Premium Set:
$64.95

Standard Set:
$56.95

Select Option:


Quantity:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 51.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Concert II and Twin II (Paul Rivera design) from 1982-1987.   (Not for the vintage Concert Amps from the 1960s.   Not for the Concert Amp [Pro Tube Series] PR245.   Not for the Concert Reverb Amp PR450 from 2001-2004).  See the complete model cross reference
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 F&T 220uF-300V (Main Filters)
  • 3 70uF-100V (Decoupling, Bias Filters)
  • 2 4.7uF-450V (Decoupling Filters)
  • 6 25uF-25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-51

$48.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 52.  Contains the following filter capacitors, used as main and decoupling filters, bias filters and cathode bypass capacitors in the Fender® Super 60 "red knob" from 1988-1992.  See the complete model cross reference
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 4 F&T 100uF-350V (Main Filters)
  • 2 Axial 25uF-25V
  • 1 Radial 470uF-50V
  • 3 Radial 100uF-100V
  • 2 Radial 22uF-50V
  • 1 Radial 47uF-50V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-52

$66.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 53.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the original version of the Fender® Hot Rod Deluxe from 1996-2010.    Does not include the Hot Rod Deluxe III - for the Hot Rod Deluxe III, see the FCK-61 kit.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 1 F&T 47uF-500V (Main Filter)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 3 Radial 100uF-100V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-53

$30.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 54.  Contains the following filter capacitors, used as main and decoupling filters, and bias filters in the original version of the Fender® Hot Rod Deville from 1996-2010.    Does not include the Hot Rod Deville III (with black control panel).  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 2 F&T 100uF-350V (Main Filters)
  • 2 F&T 47uF-450V (Decoupling Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 4 Radial 100uF-100V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-54

$53.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 54A.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the  Fender® Hot Rod Deville III from 2010 to present (with black control panel).    Does not include the original Hot Rod Deville from 1996-2010.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 2 F&T 100uF-350V (Main Filters)
  • 2 F&T 47uF-500V (Decoupling Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 4 Radial 100uF-100V
  • 1 Radial 10uF-100V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-54A

$56.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 55.  Contains the following filter capacitors, used as main, decoupling, and bias filter capacitors in the Fender® "The Twin" red knob (Paul Rivera design) from 1982-1987.    Note:   This kit includes only filter capacitors - no cathode bypass capacitors are included.  See the complete model cross reference


Click on photo for larger view

  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 F&T 220uF-300V (Main Filters)
  • 4 F&T 100uF-100V (Decoupling, Bias Filters)
  • 2 F&T 47-500V (Decoupling Filters)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-55

$59.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 56.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the original versions of the Fender® Blues Deluxe and Blues Deville from 1993-2004.    Does not include the Blues Deluxe Reissue or the Blues Deville Reissue from 2005-present.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 4 F&T 100uF-350V (Main Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 4 Radial 100uF-100V
  • 1 Radial 22uF-63V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-56

$58.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 56A.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the REISSUE version of the Fender® Blues Deville from 2005 to present.    Does not include the Blues Deville from 1993-2004.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 2 F&T 100uF-350V (Main Filters)
  • 2 F&T 47uF-500V (Decoupling Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 4 Radial 100uF-100V
  • 1 Radial 22uF-63V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-56A

$56.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 56B.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the REISSUE version of the Fender® Blues DeLuxe from 2005 to present.    Does not include the Blues DeLuxe from 1993-2004.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 1 F&T 47uF-500V (Main Filter)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 3 Radial 100uF-100V
  • 1 Radial 22uF-63V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-56B

$29.95

 



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 57.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the Fender® Blues Junior and Blues Junior III from 1995-present.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 1 F&T 47uF-500V (Main Filter)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 470uF-50V
  • 2 Radial 220uF-25V
  • 1 Radial 100uF-25V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-57

$28.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 58.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the Fender® Pro Junior Versions A, B and C from 1993 through 1998. This kit includes only the power supply capacitors.  See the complete model cross reference
  • 4 F&T 22uF-500V (Main and Decoupling Filters)
  • 2 Axial 10uF-50V (Bias Filters)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-58

$27.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 58A.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the Fender® Pro Junior Versions D, E and F and the Pro Junior III from 1998 through 2017. This kit includes only the power supply capacitors.  See the complete model cross reference
  • 1 F&T 47uF-500V (Main Filter)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Axial 10uF-50V (Bias Filters)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-58A

$24.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 59.  Contains the following filter capacitors, used as main and decoupling filters, and cathode bypass capacitors in the Fender® Champion 600 from 2006 through 2011.  See the complete model cross reference.  
  • 4 Nichicon 22uF-450V (Main and Decoupling Filters)
  • 2 Axial 22uF-50V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-59

$13.95

Fender® Electrolytic Filter Capacitor Kit 60.  Contains the following capacitors, used in the Fender Pro 185, Stage 185 and London 185.  See the complete model cross reference.     This kit contains replacements for all of the electrolytic capacitors in the amplifier:
  • 2 3300uF/63V Snap-In Electrolytic Capacitors
  • 7 22uF/50V Radial Electrolytic Capacitors (replace 22uF/25V)
  • 2 100uF/16V Radial Electrolytic Capacitors
  • 6 100uF/25V Radial Electrolytic Capacitors
  • 1 4.7uF/50V Radial Electrolytic Capacitors
  • 4 2.2uF/50V Radial Electrolytic Capacitors

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-60

$26.95



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 61.  Contains the following filter capacitors, used as main and decoupling filters, bias filters in the Hot Rod Deluxe III, from 2010 to the present.    Does not include the original versions of the Fender® Hot Rod Deluxe from 1996-2010 - see kit FCK-53 for those models.  This kit includes only the power supply capacitors.  See the complete model cross reference
  • 2 F&T 100uF-350V (Main Filters)
  • 2 F&T 47uF-500V (Main Filters)
  • 2 F&T 22uF-500V (Decoupling Filters)
  • 2 Radial 1000uF-35V
  • 4 Radial 100uF-100V

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-61

$49.95


Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 62.  Contains the following capacitors, used as main filters, decoupling filters, and cathode bypass capacitors in the Fender 5E9 and 5E9A Tremolux from 1955 to 1956.  (Note: Some late 1956 5E9As actually have the 5G9 circuit, and require the FCK-63 capacitor kit).  See the complete model cross reference

  • 3 TAD Gold 16uF-475 (Main and Decoupling Filters)
  • 4 25uF-25V (Bias Filters)

Download the installation guidelines.

Part #FCK-62

$18.95


Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 63.  Contains the following capacitors, used as main filters, decoupling filters, bias filters and cathode bypass capacitors in the Fender 5G9 Tremolux from 1957 to 1960.  See the complete model cross reference

  • 4 F&T 22uF-500V (Main and Decoupling Filters)
  • 2 Axial 8uF-150V (Bias Filters)
  • 2 Axial 25uF-25V (Cathode Bypass)

Download the installation guidelines.

Part #FCK-63

$29.95


Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 64.  Contains the following capacitors, used as main filters, decoupling filters, bias filters and cathode bypass capacitors in the Fender 75 Amp from 1980 to 1982.  See the complete model cross reference

  • 3 F&T 22uF-500V (Decoupling Filters)
  • 2 F&T 220uF-300V (Main Filters)
  • 2 Axial 70uF-100V (Decoupling, Bias Filters)
  • 5 Axial 25uF-25V (Cathode Bypass)

Download the installation guidelines.

Part #FCK-64

$44.95


Click on photo for
larger view

Fender® Electrolytic Filter Capacitor Kit 65.  Contains the following capacitors, used as main filters, decoupling filters, bias filters and cathode bypass capacitors in the Fender Music Master Bass Amp from 1970 to 1982.   Covers both the versions with 6AQ5A and 6V6 power tubes.  See the complete model cross reference

  • 3 F&T 22uF-500V (Main & Decoupling Filters)
  • 1 I.C 2.2uF-100V (Cathode Bypass)
  • 1 I.C. 10uF-50V (Cathode Bypass)
  • 1 I.C. 22uF-50V (Cathode Bypass)

Download the installation guidelines.

Part #FCK-65

$21.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 70.  Contains the following electrolytic filter capacitors, used in the Fender Bassman 5E6 and 5E6A, and the Fender Twin 5E8 and 5E8A from 1955-1957.  See the complete model cross reference
  • 4 TAD Gold 16uF/475V (Main & Decoupling Filters)
  • 1 Ruby Gold 100uF/100V (Cathode Bypass, replaces 100uF/25v)
  • 1 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 1 TAD Gold 25uF/25V (Cathode Bypass)
  • 1 Axial 220uF/25V (Cathode Bypass, replaces 250uF/6V)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-70

$25.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 71.  Contains the following electrolytic filter capacitors, used in the Fender Bassman 5F6 and 5F6A and the Fender Twin 5F8A from 1958-1960.  See the complete model cross reference
  • 4 Epcos 22uF/560V (Main & Decoupling Filters)
  • 1 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 2 Axial 8uF/150V (Bias Filters)
  • 1 Axial 220uF/16V (Cathode Bypass, replaces 250uF/6V)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-71

$24.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 72.  Contains the following electrolytic filter capacitors, used in the Fender Deluxe 5E3 Narrow Panel Tweed from 1955-1960.  See the complete model cross reference
  • 3 TAD Gold 16uF/475V (Main & Decoupling Filters)
  • 3 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-72

$16.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 73.  Contains the following electrolytic filter capacitors, used in the Fender Champ 5F1 Narrow Panel Tweed Combo from 1956-1964.  See the complete model cross reference
  • 1 TAD Gold 16uF/475V (Main Filter, replaces 16uF/450V)
  • 2 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 2 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-73

$14.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 74.  Contains the following electrolytic filter capacitors, used in the Fender Champ 5E1 Narrow Panel Tweed Combo from 1955-1956.  See the complete model cross reference
  • 3 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 2 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-74

$14.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 75.  Contains the following electrolytic filter capacitors, used in the Fender 5B1 Champion 600 from 1949-1953, the 5C1 Champ (1954-1955), and the Princeton 5F2 Narrow Panel Tweed Combo from 1956-1957.  See the complete model cross reference.  
  • 3 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 1 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-75

$12.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 76.  Contains the following electrolytic filter capacitors, used in the Fender Princeton 5F2A Narrow Panel Tweed Combo from 1957-1960.  See the complete model cross reference
  • 2 TAD Gold 16uF/475V (Main Filters)
  • 2 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 2 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-76

$19.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 77.  Contains the following electrolytic filter capacitors, used in the Fender Pro 5E5 Narrow Panel Tweed from 1955.  See the complete model cross reference
  • 4 TAD Gold 16uF/475V (Main & Decoupling Filters)
  • 3 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-77

$20.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 78.  Contains the following electrolytic filter capacitors, used in the Fender Pro 5E5A from 1956-1960, the Fender Super 5E4A from 1955, and the Fender Super 5F4 from 1956-1960.  See the complete model cross reference
  • 3 TAD Gold 16uF/475V (Main & Decoupling Filters)
  • 1 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 1 F&T 100uF/100V (Cathode Bypass, replaces 100uF/25v)
  • 2 TAD Gold 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-78

$22.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 79.  Contains the following electrolytic filter capacitors, used in the Fender Twin 5F8 from 1958.  See the complete model cross reference
  • 4 Epcos 22uF/560V (Main & Decoupling Filters)
  • 1 TAD Gold 8uF/475V (Decoupling Filters, replaces 8uF/450V)
  • 2 Axial 8uF/150V (Bias Filters)
  • 1 Axial 220uF/16V (Cathode Bypass, replaces 250uF/6V)
  • 1 25uF/25V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-79

$25.95

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 80.   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors in the Fender 30 from 1980-1981.  See the complete model cross reference
Available in Top Premium (F&T/Sprague), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands).   Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

Top Premium Set:

4 F&T 16uF-475V
2 F&T 220uF-300V
2 F&T 100uF-100V
5 Sprague 25uF-50V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$85.95
Free USA shipping
on this kit!

Pro Set:

4 TAD Gold 16uF-475V
2 TAD Gold 220uF-350V
2 100uF-100V
5 TAD Gold 25uF-25V
2 2.2K-2W Resistors
1 10K-2W Resistor
2 220K-1W Resistors

$56.95

Standard (OEM) Set:

4 DJE 16uF-475V
2 I.C. 220uF-300V
2 I.C. 100uF-100V
5 I.C. 22uF-50V
2 2.2K-2W Resistors
1 10K-2W Resistor
2 220K-1W Resistors

$46.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

4 16uF-475V
2 220uF-350V
2 70uF-100V
5 25uF-25V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$34.95

See the model cross reference for applicable models.   Download the installation guidelines.

Part #FCK-80

Top Premium Set:
$85.95

Pro Set:
$56.95

Standard Set:
$46.95

Basic Economy Set:
$34.95

Select Option:


Quantity:


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 81.  Contains the following electrolytic filter capacitors, used in the Fender 57 Deluxe Reissue from 2009 to 2012.  See the complete model cross reference
  • 3 F&T 16uF/475V (Main & Decoupling Filters)
  • 3 I.C 22uF/50V (Cathode Bypass, replaces 25uF/50V)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-81

$29.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 82.  Contains the following electrolytic filter capacitors, used in the Brownface Fender 63 Vibroverb Reissue from 1990 to 1995.  See the complete model cross reference
  • 5 F&T 22uF/500V (Main & Decoupling Filters)
  • 1 F&T 47uF/500V (Decoupling Filter, replaces 47uF/350V)
  • 6 Radial 22uF/50V (Cathode Bypass, replaces 22uF/25V)
  • 1 Radial 22uF/63V (Bias Filter)
  • 1 Radial 100uF/100V (Bias Filter)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-82

$47.95

Fender® Electrolytic Filter Capacitor Kit 83.  Contains the following electrolytic filter capacitors, used in the Blackface Fender 64 Vibroverb Custom from 2003 to 2008.  See the complete model cross reference
  • 2 F&T 220uF/300V (Main Filters, replaces 220uF/285V)
  • 2 F&T 22uF/500V (Decoupling Filters)
  • 2 F&T 47uF/500V (Decoupling Filters, replaces 47uF/350V)
  • 7 Axial 22uF/50V (Cathode Bypass, replaces 22uF/25V)
  • 1 Axial 4.7/50V (Footswitch Filter)
  • 1 Radial 22uF/63V (Cathode Bypass)
  • 1 Axial 100uF/100V (Bias Filter)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-83

$59.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 84.  Contains the following electrolytic filter capacitors, used in the Fender 57 Twin Reissue from 2009 to 2012.  See the complete model cross reference
  • 5 F&T 22uF/500V (Main and Decoupling Filters)
  • 1 F&T 100uF/100V (Bias Filter)
  • 1 Axial 22uF/50V (Cathode Bypass, replaces 22uF/25V)
  • 1 Axial 220uF/16V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-84

$33.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 85.  Contains the following electrolytic filter capacitors, used in the Fender Deluxe Reverb II from 1982-1986.  See the complete model cross reference.    The Deluxe Reverb II has 11 front panel controls, and the front panel is shown below:
  • 1 CE Mfr 80-40-20-20uF/525V (Main and Decoupling Filters)
  • 1 Epcos 22uF/560V (Decoupling Filter)
  • 2 Axial 4.7uF/450V (Decoupling Filters)
  • 2 Axial 70uF/100V (Bias Filters)
  • 5 Axial 25uF/25V (Cathode Bypass)
  • 1 4.7K-2 Watt Resistor

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-85

$67.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 86.  Contains the following electrolytic filter capacitors, used in the Fender Champ II from 1982-1983.  See the complete model cross reference.    The Champ II has 4 front panel controls, and the front panel is shown below:
  • 1 CE Mfr 80-40-20-20uF/525V (Main and Decoupling Filters)
  • 1 Axial 4.7uF/450V (Decoupling Filter)
  • 2 Axial 70uF/100V (Bias Filters)
  • 3 Axial 25uF/25V (Cathode Bypass)
  • 1 1K-2 Watt Resistor
  • 2 10K-2 Watt Resistors

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-86

$64.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 87.  Contains the following electrolytic filter capacitors, used in the Fender Princeton Reverb II from 1982-1986.  See the complete model cross reference.    The Princeton Reverb II has 8 front panel controls, and the front panel is shown below:
  • 1 CE Mfr 80-40-20-20uF/525V (Main and Decoupling Filters)
  • 1 Axial 4.7uF/450V (Decoupling Filter)
  • 2 Axial 70uF/100V (Bias Filters)
  • 3 Axial 25uF/25V (Cathode Bypass)
  • 1 4.7K-2 Watt Resistor
  • 1 10K-2 Watt Resistors

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-87

$64.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 88.  Contains the following electrolytic filter capacitors, used in the Fender Bassman 20 Combo from 1982-1983.  See the complete model cross reference.    The Bassman 20 has 4 front panel controls and one input jack, and the front panel is shown below:
  • 1 CE Mfr 80-40-20-20uF/525V (Main and Decoupling Filters)
  • 2 Axial 70uF/100V (Bias Filters)
  • 2 Axial 25uF/25V (Cathode Bypass)
  • 1 1K-2 Watt Resistor
  • 2 10K-2 Watt Resistors

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-88

$62.95


Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 89.  Contains the following electrolytic filter capacitors, used in the Fender Super Champ from 1982-1983.  (Not for the Super Champ XD or Super Champ X2)   See the complete model cross reference.   The Super Champ has 6 front panel controls, and the front panel is shown below:
  • 1 CE Mfr 80-40-20-20uF/525V (Main and Decoupling Filters)
  • 1 Axial 4.7uF/450V (Decoupling Filter)
  • 1 Axial 70uF/100V (Bias Filter)
  • 4 Axial 25uF/25V (Cathode Bypass)
  • 1 1K-2 Watt Resistor
  • 1 4.7K-2 Watt Resistor
  • 1 10K-2 Watt Resistor

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-89

$66.95

Premium Capacitor Set Shown:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 90.  Contains the following filter capacitors, used as main and decoupling filters, and cathode bypass capacitors in the Fender® 5A3, 5C3 or 5D3 Deluxe (Tweed) from 1948-1955.  Available in Top Premium or Pro versions.  See the complete model cross reference

Top Premium Set:

3 F&T 16uF-475V
2 Sprague 25uF-50V
2 10K-2W Resistor

$36.95

Pro Set:

3 Tube Amp Doctor 16uF-475V
2 TAD Gold 25uF-25V
2 10K-2W Resistor

$16.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-90

Top Premium Set:
$36.95

Pro Set:
$16.95
  

Select Option:


Quantity:

Premium Capacitor Set Shown:



Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 91.  Contains the following filter capacitors, used as main and decoupling filters, and cathode bypass capacitors in the Fender® 5B3 Deluxe (Tweed) from 1953-1955.  Available in Top Premium or Pro versions.  See the complete model cross reference

Top Premium Set:

3 F&T 22uF-500V
2 Sprague 25uF-50V
2 10K-2W Resistor

$23.95

Pro Set:

3 Tube Amp Doctor 22uF-500V
2 TAD Gold 25uF-25V
2 10K-2W Resistor

$18.95

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-91

Top Premium Set:
$23.95

Pro Set:
$18.95
  

Select Option:


Quantity:

 

Capacitor Kit, for the Fender® Prosonic Head and Combo models from the mid 1990s   Contains all of the electrolytic capacitors in the amplifier.  All capacitors are of the same OEM quality as the original capacitors, manufactured by Illinois Capacitor.

  • 2 100uF-350V (Main Filters)
  • 2 47uF-500V (Decoupling Filters)
  • 1 10uF-500V (Decoupling - replaces 4.7uF-500V)
  • 3 100uF-100V (Bias Supply and Relay Supply Filters)
  • 4 2.2uF-100V (Cathode Bypass - replaces 2.2uF-50V)
  • 1 22uF-50V (Cathode Bypass)
  • 1 2200uF-50V (Relay Supply Filter)

Part # FCK-92

$49.95

 

Click on photo for
larger view

Capacitor Kit, for the Fender® Champ 12 (Red Knob - 1987-1992)  Contains all of the electrolytic capacitors in the amplifier.  All capacitors are of the same OEM quality as the original capacitors, manufactured by Illinois Capacitor.

  • 4 47uF-500V (Main Filters - replaces 47uF-350V)
  • 2 220uF-100V (Power Tube Cathode Bypass - replaces 220uF-35V )
  • 1 22uF-50V (Preamp Tube Cathode Bypass - replaces 22uF-16V)

Part # FCK-93

$37.95

 

Capacitor Kit, fits Fender® Princeton 65 (PR403) manufactured from 1999 through 2002.   Contains the power supply radial electrolytic capacitors for this model.    (Does not contain any non-power supply capacitors)   Contains (2) 2200uF-50V, (2) 47uF-50V, and (2) 10uF-50V.   Note:   For the Princeton 65 only; not for the Princeton 65 DSP model nor the `65 Princeton Reverb Reissue.
Part # FCK-94

$5.95

 

Capacitor Kit, fits Fender® Princeton Chorus (PR82) manufactured from 1988 through 1992.   Contains the power supply radial electrolytic capacitors for this model.    (Does not contain any non-power supply capacitors)   Contains (2) 4700uF-35V, and (2) 47uF-50V  Note:   For the "red knob" Princeton Chorus only (also sometimes called the Princeton Stereo Chorus).
Part # FCK-95

$12.95

Top Premium Capacitor Set Shown:

Click on photo for
larger view
Fender® Electrolytic Filter Capacitor Kit 201.   Used in the Fender PA-100 (1972-1976).   Available in Top Premium (F&T), Pro (Tube Amp Doctor/Ruby Gold), Standard OEM (Illinois Capacitor), or Basic Economy (various select brands). This kit contains main and bias filter capacitors - no cathode bypass capacitors are included.  Contains the following capacitors, used as main filters and bias filter capacitors:
 

Top Premium Set:

3 F&T 22uF-500V
2 F&T 100uF-350V
2 F&T 100uF-100V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$52.95
 

Pro Set:

3 TAD Gold 22uF-500V
2 Ruby Gold 100uF-350V
2 100uF-100V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$44.95
 

Standard (OEM) Set:

3 I.C. 22uF-500V
2 I.C. 100uF-350V
2 I.C. 100uF-100V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$37.95

Basic Economy Set:

Our Basic Economy Capacitor Kits contain capacitors of multiple selected brands, chosen for their quality and economical price:

 

3 20uF-500V
2 100uF-350V
2 100uF-100V
1 2.2K-2W Resistor
1 10K-2W Resistor
2 220K-1W Resistors

$13.95

Download the installation guidelines.

Part #FCK-201

Top Premium Set:
$52.95

Pro Set:
$44.95

Standard Set:
$37.95

Basic Economy Set:
$13.95

Select Option:


Quantity:

 

Fender Cross Reference Table:

Amplifier Model and Date Code

Cap. Kit

Bandmaster Amp 5E7 (Narrow Panel Tweed 3x10 combo, 1955-1960) FCK-73
Bandmaster Amp 6G7 (Brownface 3x10 combo, 1960) FCK-34
Bandmaster Amp 6G7A (Blonde Piggyback, 1961-1963) FCK-35
Bandmaster Amp AA763, AB763, AC568 FCK-1
Bandmaster Reverb AA768 FCK-4
Bandmaster Reverb AA1069 (TFL5005D) FCK-4B
Bandmaster Reverb AA270 (TFL5005D) FCK-7
Bandmaster Reverb w/Master Volume, 45 Watt Output 1972-1974 FCK-7
Bandmaster Reverb w/Master Volume, 70 Watt Output U/L 1974-1980 FCK-10
Bantam Bass CFA7003 (1969-1971- Silverface Combo) FCK-13
Bassman AA165, AB165, AC568 FCK-18
Bassman AA864 FCK-1
Bassman AA270 FCK-11
Bassman AA371 FCK-11A
Bassman 10 or Bassman Ten (Silverface Combo, 50 watts, 1972-1976) FCK-13
Bassman 10 or Bassman Ten (Ultralinear - Silverface Combo, 75 watts, 1977-1982) FCK-13D
Bassman 5E6, 5E6A (Tweed, Narrow Panel, 1955-1957) FCK-70
Bassman 5F6, 5F6A (Tweed, Narrow Panel, 1957-1960) FCK-71
Bassman 6G6 (Blonde piggyback, 1961-1963) FCK-40
Bassman 6G6A (Blonde piggyback, 1962-1963) FCK-41
Bassman 6G6B (Blonde piggyback, 1963-1964) FCK-42
Bassman 20 (Blackface Combo, 1982-1983) FCK-88
Bassman 50 (Silverface Head, 1972-1976) FCK-11A
Bassman 70 (Silverface Head, 1977-1983) FCK-13C
Bassman 100 (Silverface Head, 1972-1976) (Not the solid-state combo from 2000) FCK-13A
Bassman 135 (Silverface Head, 1977-1983) FCK-13B
59 Bassman Reissue (Tweed Combo, 1990-present) FCK-27
Blues Deluxe (Original version only, 1993-2004) FCK-56
Blues Deluxe (Reissue version only, 2005-present) FCK-56B
Blues Deville (Original version only, 1993-2004) FCK-56
Blues Deville (Reissue version only, 2005-present) FCK-56A
Blues Junior (Original version 1995-2010) FCK-57
Blues Junior III (2010-Present) FCK-57
Bronco Amp AB764 (Silverface, 1967-1975) FCK-20
Champ 5C1 (Wide Panel Tweed, 1954-1955) FCK-75
Champ 5E1 (Narrow Panel Tweed, 1955-1956) FCK-74
Champ 5F1 (Narrow Panel Tweed, 1956-1964) FCK-73
Champ AA764 (Includes all Blackface Champs from 1964-1967) FCK-14
Champ (CBS) (Includes all Silverface Champs from 1968-1982) FCK-14
Champ II (Blackface, 4 controls, 1982-1983) FCK-86
Champ 12 (Red Knob, 1987-1992) FCK-93
Champion 600 5B1 (TV Front Tweed, 1949-1953) FCK-75
Champion 600 Reissue (2006-2011) FCK-59
Concert 6G12 (Brownface combo, 1960) FCK-34
Concert 6G12A (Brownface combo, 1961-1963) FCK-35
Concert AA763, AB763 (Not Concert II, 93 Concert PR245, or Concert Reverb PR450) FCK-1
Concert II (1982-1987)  (Not 93 Concert PR245 or Concert Reverb PR450) FCK-51
93 Concert Amp (PR245 - 1993-1995) FCK-29
Concert Reverb (PR450 - Pro Tube Series - 2001-2005) FCK-17
Deluxe Amp 5A3 (Tweed, 1948-1953) FCK-90
Deluxe Amp 5B3 (Tweed, 1953-1954) FCK-91
Deluxe Amp 5C3 (Tweed, 1954) FCK-90
Deluxe Amp 5D3 (Tweed, 1955) FCK-90
Deluxe Amp 5E3 (Narrow Panel Tweed, 1955-1960) FCK-72
Deluxe Amp 6G3 (Brownface, 1961-1963) FCK-30
57 Deluxe Reissue (2007-Present) FCK-81
Deluxe Reverb AA763, AB763, AB868 FCK-6
Deluxe Reverb A1172, A1270, Volume Boost Model (late 70s) FCK-8
Deluxe Reverb II (Blackface, 11 controls, 1982-1986) FCK-85
65 Deluxe Reverb Reissue (Blackface, 1993-present) FCK-23
68 Custom Deluxe Reverb (Silverface, Drip Edge, 2007-present) FCK-23
Dual Showman Reverb AA769 (1969) FCK-4B
Dual Showman Reverb AA270 (1970) FCK-12
Dual Showman Reverb w/Master Volume, but NO pull switch on MV, 1971-1972 FCK-9
Dual Showman Reverb w/Master Volume & Push/Pull Switch, 100 W 1972-1974 FCK-9A
Dual Showman Reverb w/Master Volume, 135W Output Ultralinear 1974-1980 FCK-10
Fender 30 (1980-1981 - Blackface, 2 Channels, 9 Controls) FCK-80
Fender 75 (1980-1982 - Blackface, Head or Combo, 8 Controls) FCK-64
Harvard 6G10 (Tweed, 1961-1962) FCK-31
Hot Rod Deluxe (1996-2010) FCK-53
Hot Rod Deluxe III (2010-Present) FCK-61
Hot Rod Deville (1996-2010) FCK-54
Hot Rod Deville III (2010-Present) FCK-54A
London 185 (Solid State, 1989-1991) FCK-60
Music Master Bass Amp (6AQ5A power tubes, 1970-1982) FCK-65
Music Master Bass Amp (6V6 power tubes, 1970-1982) FCK-65
PA-100 (100 Watts, 1972-1976) FCK-201
PA-135 (135 Watts, 1976-1979) FCK-10A
Pawn Shop Excelsior (PR2298, 2012-2015) FCK-44
Princeton 65 (PR403, 1999-2002) FCK-94
Princeton Amp 5F2 (1956-1957 - Narrow Panel Tweed) FCK-75
Princeton Amp 6G2 - Without Reverb! (1963-1964 - Blackface) FCK-45
Princeton Amp AA964, AB1270 - Without Reverb! (1964-1979 - Blackface/Silverface) FCK-15
Princeton Chorus (PR82, 1988-1992, Red Knob) FCK-95
Princeton Reverb Amp AA764, AA1164, AB1270 (1964-1981 - Blackface, Silverface) FCK-16
Princeton Reverb II (Blackface, 8 controls, 1982-1986) FCK-87
68 Custom Princeton Reverb (2012-Present, Silverface, Drip Edge) FCK-22
Pro Amp 5E5A (Narrow Panel Tweed combo, 1956-1960) FCK-78
Pro Amp 6G5A (Brownface combo, 1962-1963) FCK-36
Pro Amp AA763 (1963) FCK-3
Pro Amp AB763 (1963) FCK-1
Pro Amp AA763 (1963) FCK-3
Pro Junior (Rev A, B, and C - 1993-1998) FCK-58
Pro Junior and Pro Junior III (Rev D, E, and F - 1998-2017) FCK-58A
Pro Reverb AA165 (1965) FCK-4
Pro Reverb AB668 (1968) FCK-4C
Pro Reverb AA1069 (1969) FCK-4B
Pro Reverb AA270 1970-1972 FCK-4B
Pro Reverb w/Master Volume, 45 Watt Output 1973-1974 FCK-7
Pro Reverb w/Master Volume, 70 Watt Output Ultralinear 1974-1980 FCK-10
Pro Reverb (PR448 - Pro Tube Series - 2001-2005) FCK-17
Pro 185 (Solid State, 1989-1991) FCK-60
Prosonic (Head or Combo, 1996-2002) FCK-92
63 Reverb Unit (Reissue, 1994-2016) FCK-28
Reverb Unit 6G15 (1961-1966) FCK-28A
Quad Reverb w/Master Volume, but NO pull switch on MV, 1971-1972 FCK-9
Quad Reverb w/Master Volume & Push/Pull Switch, 100 Watts, 1972-1974 FCK-9A
Quad Reverb w/Master Volume, 135W Output Ultralinear 1974-1980 FCK-10
Fender 75 (1980-1982 - Blackface, Head or Combo, 8 Controls) FCK-64
Showman 6G14 (Blonde piggyback, 1960) FCK-37
Showman 6G14A (Blonde piggyback, 1961) FCK-34
Showman AA763, AB763, AC568 (1963-1968) FCK-1
Showman Reverb AA768 (1968) FCK-4
Stage 185 (Solid State, 1989-1991) FCK-60
Super 5E4A, 5F4 (Narrow Panel Tweed combo, 1955-1960) FCK-78
Super 6G4 (Brownface combo, 1960-1961) FCK-34
Super 6G4A (Brownface combo, 1962-1963) FCK-35
Super 60 (Red Knob, 1988-1992) FCK-52
Super Bassman (Silverface Head CFA7002, 1969-1971) (Not the blackface reissue) FCK-13
Super Champ (Blackface Combo, 1982-1983) (Not the Super Champ XD or X2) FCK-89
Super Reverb AA763 (1963) FCK-5
Super Reverb AB763, AB568 (1963-1969) FCK-4
Super Reverb AA1069 (1969-1970) FCK-4B
Super Reverb AA270 (1970-1971) FCK-7
Super Reverb w/Master Volume, 45 Watt Output 1972-1974 FCK-7
Super Reverb w/Master Volume, 70 Watt Output Ultralinear 1974-1980 FCK-10
65 Super Reverb Reissue, (Blackface, 2000-present) FCK-24 or
FCK-24A
Super Six Reverb - No Master Volume, 1971 FCK-7
Super Six Reverb w/Master Volume, but NO pull switch on MV, 1972 FCK-9
Super Six Reverb w/Master Volume & Push/Pull Switch, 100 Watts 1972-1974 FCK-9A
Super Six Reverb w/Master Volume, 135W Output Ultralinear 1974-1980 FCK-10
Super Twin, 180 Watt Output 1975-1976 FCK-19
Super Twin Reverb, 180 Watt Output 1977-1981 FCK-19
Fender 30 (1980-1981 - Blackface, 2 Channels, 9 Controls) FCK-80
Tremolux 5E9 (Tweed, 1955) FCK-62
Tremolux 5E9A (Tweed, 1955-56) (Note: Some late 1956 5E9As have the 5G9 circuit) FCK-62
Tremolux 5G9 (Tweed, 1957-1960) FCK-63
Tremolux 6G9 (Blonde Piggyback, 1961) FCK-32
Tremolux 6G9A, 6G9B (Blonde Piggyback, 1962-1963) FCK-33
Tremolux AA763, AB763 (1973) FCK-2
Twin 5E8, 5E8A (Narrow Panel Tweed combo, 1955-1957) FCK-70
Twin 5F8 (Narrow Panel Tweed combo, 1958) FCK-79
Twin 5F8A (Narrow Panel Tweed combo, 1959-1960) FCK-71
Twin 6G8 (Blonde combo, 1961) FCK-38
Twin 6G8A (Blonde combo, 1962-1963) FCK-34
the Twin (Red Knob, 1987-1994) FCK-55
94 Twin Amp (1994-1998, Rev A, B or C circuit board) FCK-21
94 Twin Amp (1999-2001, Rev D or E circuit board) FCK-21D
Twin Amp (PR449 - Pro Tube Series - 2001-2005) FCK-17
57 Twin Reissue (2009-2012, Tweed, Custom Shop) FCK-84
Twin Reverb AB763 (1963-1968) FCK-4
Twin Reverb AC568, AA769 (1968-1970) FCK-4A
Twin Reverb AA270 (1970-1971) FCK-12
Twin Reverb w/Master Volume, but NO pull switch on MV, 1971-1972 FCK-9
Twin Reverb w/Master Volume & Push/Pull Switch, 100 Watts 1972-1974 FCK-9A
Twin Reverb w/Master Volume, 135W Output Ultralinear 1974-1980 FCK-10
65 Twin Reverb Reissue (Blackface, 1991-present) FCK-25
68 Custom Twin Reverb Reissue (Silverface, 2009-present) FCK-25
Twin Reverb II (1982-1986) FCK-51
Vibro Champ AA764 (Silverface, 1967-1975) FCK-20
Vibro King (1994-1997, with EL84 or 6BQ5 reverb driver tube) FCK-50
Vibro King (1997-present, with 6V6 reverb driver tube) FCK-50A
Vibrolux 5E11, 5F11 (Narrow Panel Tweed combo, 1956-1961) FCK-72
Vibrolux 6G11, 6G11A (Brownface, 1961-1963) FCK-33
Vibrolux AA763, AB763 (1963) FCK-2
Vibrolux Reverb AA964 (1964-1968) FCK-6
Vibrolux Reverb AB568 (1968-1969) FCK-6A
Vibrolux Reverb AA270 (1970-1976) FCK-8C
Vibrolux Reverb with pull-boost switch on the Volume control (1977-1982)
See notes on kits FCK-8A and FCK-8B to see which kit is right for your version.*
FCK-8A or
FCK-8B*
"Custom" Vibrolux Reverb Reissue (Blackface, White Knobs, 1995-2010) FCK-26
Vibrasonic 6G13A (Brownface 1x15" Combo, 1961-1963) FCK-35
Vibrosonic Reverb w/Master Volume, but NO pull switch on MV, 1971-1972 FCK-9
Vibrosonic Reverb w/Master Volume & Push/Pull Switch, 100 Watts 1972-1974 FCK-9A
Vibrosonic Reverb w/Master Volume, 135W Output Ultralinear 1974-1980 FCK-10
Vibroverb 6G16 (Brownface combo, 1963) FCK-39
63 Vibroverb Reissue (Brownface combo, 1990-1995) FCK-82
64 Vibroverb Custom (Blackface combo, 2003-2008) FCK-83
Vibroverb AA763 (1963) FCK-5
Vibroverb AB763 (1963) FCK-4
 
 

Unable to find your exact amp model (with identical date code)?    Contact us for more information.

Unable to find the date code?    No tube chart in the cabinet?  Contact us for more information.

For vintage amps (blackface and some silverface), the date code is located on the tube chart inside the back of the amplifier cabinet:


 

Copyright ©2021 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov