Lamps

 


 

Lamps

   

Click on photo for
larger view
NEW! BRIGHT LED INDICATOR LAMP, REPLACES #47 BULB, T-3-1/4, 6.3V, BAYONET BASE
Drop-in replacement long life LED replacement lamp for pilot lamps.  Fits Fender amps which are designed for the P-47 type incandescent bulb (including most Fender amps from the 1950s through the present).   The LED replacement is long lasting, runs much cooler, and is substantially brighter than the P-47 incandescent bulb.  If  less brightness is desired, install a series resistor feeding the lamp socket (1/4 or ½ watt, value between 560Ω and 1KΩ).  Sold individually.  Add new pizzazz to your amp with a brighter lamp on the front panel, and one which pays for itself in the long run with exceptionally long life.   Works on 6 volts, AC or DC.   Color is warm white.   NOTE: NOT RECOMMENDED FOR USE WITH THE PURPLE J-115P JEWEL - WILL RESULT IN A DEEP BLUE COLOR RATHER THAN PURPLE.     ALSO, NOT FOR USE WITH THE LH-110 LAMP HOLDER.
Part #LED-47
$2.95  


Click on photo for
larger view
NEW!  COOL BLUE BRIGHT OUTPUT LED INDICATOR LAMP, REPLACES #47 BULB, T-3-1/4, 6.3V, BAYONET BASE
Drop-in replacement long life BLUE OUTPUT LED replacement lamp for pilot lamps.  Fits Fender amps which are designed for the P-47 type incandescent bulb (including most Fender amps from the 1950s through the present).   (Not for use, however, with the LH-110 lamp holder). The LED replacement is long lasting, runs much cooler, and is substantially brighter than the P-47 incandescent bulb. Works on 6 volts, AC or DC. Output color is cool blue.  When used with different colored jewels, creates a different color and a different vibe!  See the results below:

Jewel Color

Resulting Look

Brightness Level

JL-115A Amber Yellow High
JL-115B Blue Medium Blue High
JL-115C Clear Crystal Blue High
JL-115G Green Light Green High
JL-115P Purple Deep Blue Medium
JL-115Q Aqua Light to Med. Blue High
JL-115R Red Orange Medium
JL-115V Violet Bluish Violet Low
JL-115W White Baby Blue Low

Part #LED-47B

$2.95  


Click on photo for
larger view
INDICATOR LAMP, #47, T-3-1/4, 6.3V, .15 AMP, BAYONET BASE
P-47
General replacement lamps for dials, indicators, etc. Sold individually.  6.3V
Part #P-47
$0.99  


Click on photo for
larger view
BAD CAT AMPLIFIER LOGO ILLUMINATION LAMP SET. #259, 6V, .25 AMP, WEDGE BASE
Long life general replacement lamps for backlighting the Bad Cat logo on many models of Bad Cat amplifiers.   Set of 6 lamps.
Part #LP-259-6
$5.95
(for a set of 6 lamps)
 


Click on photo for
larger view
REPLACEMENT BULB FOR MORLEY® EFFECTS AND VOLUME PEDALS
Long life replacement bulb used for both the pilot lamp and also to drive the photocell in all Morley pedals from 1983 through current models.  Pedal not working?   In most cases, it just needs a new bulb.
Part #L-387
$1.99  


LED Colors Available:

Click on photo for
larger view
5mm DIFFUSED LED - CHOICE OF COLORS
Standard 5mm (3/16") diameter diffused LED found in many guitar amplifiers and effects pedals.  Available in white, red, blue, green, or yellow.   This 5mm size is commonly called the T-1-3/4 size.  On LEDs the longer leg (the anode) goes to the positive voltage supply.   LEDs need a DC supply voltage and a resistor in series with them to limit current.   For a 9V supply, a 470 ohm resistor works well.   For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.

Part #LED-5D
$0.59
(per LED)
 

Select Option:


Quantity:


LED Colors Available:

Click on photo for
larger view
3mm DIFFUSED LED - CHOICE OF COLORS
Standard 3mm (1/8") diameter diffused LED found in many guitar amplifiers and effects pedals.  Available in white, red, blue, green, or yellow.   This 3mm size is commonly called the T-1 size.  On LEDs the longer leg (the anode) goes to the positive voltage supply.   LEDs need a DC supply voltage and a resistor in series with them to limit current.   For a 9V supply, a 470 ohm resistor works well.   For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.

Part #LED-3D
$0.39
(per LED)
 

Select Option:


Quantity:


Click on photo for
larger view
SUPER-BRIGHT 5mm RED WATERCLEAR LED
Standard 5mm (3/16") diameter waterclear red LED found in many guitar amplifiers and effects pedals.   A red waterclear LED looks clear when it is off, and emits a bright red light when power is applied.  On LED's the longer leg (the anode) goes to the positive voltage supply.   LED's need a DC supply voltage and a resistor in series with them to limit current.   For a 9V supply, a 470 ohm resistor works well.   For 12 volts, a 680 resistor resistor, and for 15 volts, a 1K resistor.

Part #LED-5R-WC
$0.59  


Click on photo for
larger view
FENDER SQUARE 5mmX5mm DIFFUSED RED LED
Replaces the channel-switching indicator LED or the power indicator in several Fender amps and also in many Fender footswitches.   Replaces original Fender part number 028039.  Found in Blues Deluxe, Blues Deville, Hot Rod Deluxe, Hot Rod Deville, Deluxe 112, Deluxe 112 Plus, Ultimate Chorus, Princeton 112, Princeton 112 Plus, Powerstage 100, Roc Pro 700, BXR200, KXR60, KXR100, KXR200, Frontman 25R, Pro Reverb and Twin Amp (Pro Tube Series), Acoustasonic Jr.   Also found in the 028122 and 050419 Fender footswitches.   This LED is part of the circuitry in many Fender footswitches, and its failure often means the channel switching stops functioning correctly.  This LED is red only - will not replace the bi-color footswitches used in some of these amps.

Part #LED-573
$1.75  


LED Colors Available:

Click on photo for
larger view
BEZEL-MOUNTED LED WITH BUILT-IN RESISTOR
The ultimate time saver!  This is an LED mounted in a bezel with a resistor and shrink wrapped wires.
Length is 19mm long - 16mm of which is below the mounting area.  These Prewired LEDs are designed for 8V to 12V DC - no dropping resistor needed.   The length of the wire is about 6.5"   Mounting hole is 8mm, LED color choice is red, amber, green, blue or white.
Part #LED-725-X
$1.95  

Select Option:


Quantity:



Click on photo for
 larger view
PILOT LAMP HOLDER, REPLACEMENT FOR FENDER®
Pilot lamp holder, fits 11/16" Chassis Hole
Bezel inner diameter: 0.570" Bezel inner diameter (including threading): 0.527"    Works with a standard bayonet lamp such as the 6.3V #47 lamp.   Accepts all of the colored jewels on this page.

Part #LH-124
$3.95  



Click on photo for
 larger view
PILOT LAMP HOLDER, REPLACEMENT FOR MANY BRANDS.
Lamp holder. Relampable front panel indicator accepts a variety of T-2 and T-3 1/4 miniature bayonet lamps. 11/16" chassis hole.  Accepts all of the colored jewels on this page.     Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs) Rating: 125V, 75W. Not recommended for use with the LED-47 or LED-47B, as the sleeve in the holder is not compatible with the LED.

Part #LH-110
$6.99  


RED

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, RED, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, red jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110R 
$8.95  


AMBER

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, AMBER, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, amber jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110A 
$8.95  


BLUE

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, BLUE, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, blue jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110B 
$8.95  


CLEAR

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, CLEAR, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, clear jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110C
$8.95  


GREEN

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, GREEN, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, green jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110G
$8.95  


VIOLET

Click on photo for
 larger view
PREMIUM PILOT LAMP ASSEMBLY, VIOLET, REPLACEMENT FOR MESA BOOGIE, FENDER® AND OTHER AMP BRANDS.  COMPLETE WITH #47 BULB.
Complete pilot lamp assembly:  Includes premium pilot lamp holder, violet jewel and a #47 bulb. Fits 11/16" chassis hole. Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring. Holder not designed for use with LED replacements, such as the LED-47 or LED-47B.

Part #FLA-110V
$8.95  


RED

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, RED, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, red jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124R

Starting at
$6.95
Select Option:




BLUE

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, BLUE, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, blue jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124B

Starting at
$6.95
Select Option:




AMBER

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, AMBER, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, amber jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124A

Starting at
$6.95
Select Option:




CLEAR

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, CLEAR, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, clear jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124C

Starting at
$6.95
Select Option:




GREEN

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, GREEN, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, green jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124G

Starting at
$6.95
Select Option:




VIOLET

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, VIOLET, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, violet jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124V

Starting at
$6.95
Select Option:




WHITE

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, WHITE, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, white jewel and your choice of #47 bulb or equivalent LED-47.  The LED option provides a cooler, yet brighter light with much longer life.  LED color is `warm white`, for a color very close to that of a bulb.   Fits 11/16" chassis hole.   Designed for 6 volts (filament voltage in tube amps).  Ready for installation and wiring.

Available with 6V `warm white` LED or standard 6V incandescent bulb - choose in "Options"

Part #FLA-124W

Starting at
$6.95
Select Option:




PURPLE

Click on photo for
 larger view
PILOT LAMP ASSEMBLY, PURPLE, REPLACEMENT FOR FENDER®
Complete pilot lamp assembly:  Includes pilot lamp holder, purple jewel and #47 bulb complete, fits 11/16" chassis hole.   Designed for 6.3 volts. Ready for installation and wiring.

The purple color on this lamp jewel is toward the cool end of the purple/violet range - so it has more of a bluish tint to the purple color.  In fact, the lamp jewel cover looks blue if the light is not turned on.  If you prefer a warmer tone (toward the red/pink end of the scale), choose the FLA-124V violet lamp assembly.  Not available with the LED option, as the color when using an LED is a deep blue rather than purple.
Part #FLA-124P

$6.95  


Click on photo for
 larger view
Marshall® VINTAGE INDICATOR LIGHT - 6 VOLT, WITH RETAINER CLIP.
Indicator light, square. 6 Volts.   Measures:  0.44" Length x 0.44" Width x 0.27" Depth.   For 3/8" diameter hole.  Used in vintage Marshall® designs such as the JMP.   6 volt lamp - designed to run off of the filament voltage line.   Original Marshall® part.   Retainer clip IS included with the light.   Read about 6V light installation here.
Part #MPL-06
$11.95  


Click on photo for
 larger view
Marshall® VINTAGE INDICATOR LIGHT - 120 VOLT.
Indicator light, square. 120 Volts. Measures: 0.47" Length x 0.47" Width x 0.09" Depth (3/8" mounting hole).   Used in vintage Marshall® designs such as the JMP.   120 volt lamp - designed to run off of the switched line voltage. Original Marshall® part.   No retainer needed on this lamp - has automatic lock-in to 3/8" mounting hole.
Part #MPL-120
$11.95


Click on photo for
 larger view
Marshall® VINTAGE INDICATOR LIGHT - PURPLE, 6V LED.
Indicator light, square. Purple, LED powered, for 6V only.   As used in the Marshall Vintage Modern models 2266, 2466, and 2266C. Original Marshall® part M-BULB-00007.
Part #MPL-007
$10.95


Click on photo for
 larger view
Marshall® VINTAGE AMBER INDICATOR LIGHT - 120 VOLT.
Indicator light, round. 120 Volts.  3/8" mounting hole.   Used in vintage Marshall® designs such as the JTM-45 and JTM-100 from the early 1960s.  Also found in other vintage British amps.   120 volt lamp - designed to run on the switched line voltage (North America only).   Mounting nut is included.
Part #MPL-6010
$9.95  

 

Speaker Protector Lamps

   

Click on photo for
larger view
1141 Speaker Protection Limiter Lamp
This lamp is used in many crossovers for medium sized horn drivers - this size is commonly found in Peavey.   As the audio power increases, this device heats up (and even lights up at high power levels).  As it heats its resistance increases, thereby reducing the audio power reaching the driver.   This lamp fits a standard automotive style twist receptacle on the crossover board.
Part # 1141
$1.49


Click on photo for
larger view
1156 Speaker Protection Limiter Lamp
This lamp is used in many crossovers for larger sized horn drivers - this size is commonly found in Peavey.   As the audio power increases, this device heats up (and even lights up at high power levels).  As it heats its resistance increases, thereby reducing the audio power reaching the driver.   This lamp fits a standard automotive style twist receptacle on the crossover board.
Part # 1156
$1.49


Copyright ©2021 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov