These are the most commonly replaced parts in Fender™ 65 Super Reverb Reissue models from 1995 through the present.


Pots     Knobs    Jacks     Switches     Pilot Light     Hardware
    
Reverb     Capacitor Kit     Resistors     Tube Sockets     Footswitch

      Back to Fender™ Parts Index


Photo

Description

Price Purchase

(Picture for illustrative purposes only - actual kit components will vary from this photo)

FENDER "S-L-O-W-E-R  VIBRATO" KIT FOR REISSUE AMPS This kit changes the circuit design of the vibrato to slow down the slow end of the vibrato speed control considerably, giving a much wider usable speed range.    Fast speed remains virtually unchanged, and the intensity remains the same.  Fits `65 Twin Reverb™ Reissue, `65 Super Reverb™ Reissue, `65 Deluxe Reverb™ Reissue, '65 Princeton Reverb™ Reissue, `68 Custom Twin Reverb™, `65 Custom Super Reverb™, `68 Custom Deluxe Reverb™, '68 Custom Princeton Reverb™.  Kit includes necessary parts and instructions.   Soldering capability is required.

Part #FRSVK

$1.25  


Click on photo for
larger view
 FENDER STYLE POT, SINGLE GANG - BRACKET MOUNT,  SMOOTH 1/4" SHAFT. 
Found in the Blackface Reissue versions (2000-present) of Deluxe Reverb, Princeton Reverb, Pro Reverb, Super Reverb and Twin Reverb.
POT VALUE REPLACES
FENDER PART #
APPLICATION
A10K 0037598000 MIDDLE CONTROL, 65 REISSUE MODELS:  PRO / SUPER / TWIN
C50K 0037602000 VIBRATO INTENSITY CONTROL, 65 REISSUE MODELS:  DELUXE /  PRO / SUPER / TWIN
B100K 0037600000 REVERB CONTROL, 65 REISSUE MODELS:  DELUXE / PRINCETON / PRO SUPER / TWIN.  
A250K 0037597000
0047540000
BASS AND TREBLE CONTROLS, 65 REISSUE MODELS:  DELUXE / PRINCETON / PRO / SUPER / TWIN.  VIBRATO INTENSITY CONTROL, PRINCETON REVERB REISSUE
A1M 0037596000
0036966000
VOLUME CONTROLS, 65 REISSUE MODELS:  DELUXE / PRINCETON / PRO / SUPER / TWIN.  
C3M 0037601000 VIBRATO SPEED CONTROL, 65 REISSUE MODELS:  DELUXE / PRINCETON / PRO / SUPER / TWIN

INCLUDES NUT & WASHER  (For spare or replacement nut, order the JN-1016 nut found in this section)
Part #FPHD-XX

Starting at
$3.95
Select Option:


Quantity:


Click on photo for
larger view
FENDER COMPLETE POTENTIOMETER KIT - 65 SUPER REVERB REISSUE.  Contains all 10 control pots as found in the 65 Super Reverb Reissue, from 2001 to the present.  Does not include the bias pot.
INCLUDES NUTS & WASHERS

Part #FPK-111
$48.99  


Click on photo for
larger view
POT - Fender™ BIAS POT 10K LINEAR, SCREW
Original Fender™ 10K linear, screw, bias potentiometer.  Used in the '65 Super Reverb Reissue.  Original Fender™ part # 0017502000.   Includes lock washer, smooth washer and nut.
Part #P-BPF-10KL
$4.95  


Click on photo for
larger view
KNOB, Fender™ STYLE, SET-SCREW
Fender™ style amp knob, skirted with 1-10 numbering.  Traditional "Witches Hat" design.   For vintage Fender™ amps in the original blackface and silverface series, as well as the blackface and silverface reissue series.  With set-screw, for 1/4" smooth shaft pots.  Replaces Fender™ part number 0990930000.
Part #FVSK
$5.50


Click on photo for
larger view
JACK, 1/4", Used in Fender, PCB, MONO CLOSED CIRCUIT
PCB mono closed circuit.   Original Fender™ part number 0037117000.    Nut and washer are included.
Part #J-512
$7.95  


Click on photo for
larger view
JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft
Used in the 65 Super Reverb Reissue as the main speaker out jack.  Includes nut and washer.   Genuine Fender™ part number 0021550000 (originally 021550).
Part #J-12A
$3.95


Click on photo for
larger view
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft
Found in many guitars, effects pedals, amps speaker output.  Includes nut and washer.
Part #J-11
$3.39


Click on photo for
larger view
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft
Used as the footswitch jack in the '65 Super Reverb Reissue.  Includes nut and washer.  Genuine Fender™ part number 0013043000.
Part #J-12B
$4.35


Click on photo for
larger view
SWITCH, TOGGLE - MADE BY CARLING - RATED AT 15A, 125VAC.    Two position (on/off), double pole (DPST).   Fits 1/2" chassis hole.   1/4" push on terminals.     Original Fender™ part number 003657000 (old number 036570).    Used as the power switch in the '65 Super Reverb Reissue.
Part #SW-525
$8.95  


Click on photo for
larger view
SWITCH, TOGGLE - MADE BY CARLING - RATED AT 15A, 125VAC.    Two position (on/off), single pole (SPST).   Fits 1/2" chassis hole.   1/4" push on terminals.     Original Fender™ part number 003703900 (old number 037039).    Used as the standby switch in the '65 Super Reverb Reissue.
Part #SW-515
$7.95  


Click on photo for
larger view
SWITCH, SLIDE, SWITCHCRAFT™, DPDT (6 TERMINALS),  REPLACEMENT FOR BRIGHT SWITCH IN 60s and 70s Fender™ AMPS.   Also used in many other applications, including some Electro Harmonix AC powered effects pedals, such as the Memory Man.  Also used as the slide switch on Jazzmaster and Jaquar guitars.  Used for the power switch in the vintage 60s and 70s Fender Champ, Vibro Champ, and Bronco amps. Rated at 3A, 125VAC.    Click here for physical specifications.   Two screws are included with the switch. 
Part #SW-116S - CURRENTLY OUT OF STOCK. NO NEW STOCK EXPECTED FROM SWITCHCRAFT UNTIL JULY, 2022.
$4.95  


Click on photo for
larger view
SWITCH, SLIDE, DPDT (6 TERMINALS),  MADE BY ALPHA (TAIWAN), MAY BE USED AS A REPLACEMENT FOR BRIGHT SWITCH IN 60's and 70's Fender™ AMPS.   Also used in many other applications, including some Electro Harmonix AC powered effects pedals, such as the Memory Man.  Click here for physical specifications.   Two screws are included with the switch.  See below for a kit of two of these switches with screws included for refurbishing Fender™ amps.
Part #SW-242S
$1.95  



Click on photo for
 larger view
PILOT LAMP ASSEMBLY, RED,  FENDER
Complete pilot lamp assembly:  Includes pilot lamp holder, red jewel and #47 bulb complete, fits 11/16" chassis hole.   Designed for 6.3 volts. Ready for installation and wiring in the Fender™ '65 Super Reverb Reissue.
Part #FLA-124R
$6.95  



Click on photo for
 larger view
PILOT LAMP HOLDER, REPLACEMENT FOR FENDER
Pilot lamp holder, fits 11/16" Chassis Hole
Bezel inner diameter: 0.570" Bezel inner diameter (including threading): 0.527"    Works with a standard bayonet lamp such as the 6.3V #47 lamp.   Accepts all of the colored jewels on this page.

Part #LH-124
$3.95  


RED

Click on photo for
 larger view
REPLACEMENT PILOT LAMP JEWEL, Fender™, Peavey™, Mesa/Boogie™, many others.   RED - the standard on Fenders since the 1940's.   Replaces Fender™ part number 0990952000.

Part #JL-115R
$2.99  


Click on photo for
larger view
NEW! BRIGHT LED INDICATOR LAMP, REPLACES #47 BULB,
T-3-1/4, 6.3V, BAYONET BASE

Drop-in replacement long life LED replacement lamp for pilot lamps.  Fits Fender amps which are designed for the P-47 type incandescent bulb (including most Fender amps from the 1950s through the present).   The LED replacement is long lasting, runs much cooler, and is substantially brighter than the P-47 incandescent bulb.  If  less brightness is desired, install a series resistor feeding the lamp socket (1/4 or ½ watt, value between 560Ω and 1KΩ).  Sold individually.  Add new pizzazz to your amp with a brighter lamp on the front panel, and one which pays for itself in the long run with exceptionally long life.   Works on 6 volts, AC or DC.   Color is warm white.   NOTE: NOT RECOMMENDED FOR USE WITH THE PURPLE J-115P JEWEL - WILL RESULT IN A DEEP BLUE COLOR RATHER THAN PURPLE.     ALSO, NOT FOR USE WITH THE LH-110 LAMP HOLDER.
Part #LED-47
$2.95  


Click on photo for
larger view
NEW!  COOL BLUE BRIGHT OUTPUT LED INDICATOR LAMP, REPLACES #47 BULB, T-3-1/4, 6.3V, BAYONET BASE
Drop-in replacement long life BLUE OUTPUT LED replacement lamp for pilot lamps.  Fits Fender amps which are designed for the P-47 type incandescent bulb (including most Fender amps from the 1950s through the present).   (Not for use, however, with the LH-110 lamp holder). The LED replacement is long lasting, runs much cooler, and is substantially brighter than the P-47 incandescent bulb. Works on 6 volts, AC or DC. Output color is cool blue.  When used with different colored jewels, creates a different color and a different vibe!  See the results below:

Jewel Color

Resulting Look

Brightness Level

JL-115A Amber Yellow High
JL-115B Blue Medium Blue High
JL-115C Clear Crystal Blue High
JL-115G Green Light Green High
JL-115P Purple Deep Blue Medium
JL-115R Red Orange Medium
JL-115V Violet Bluish Violet Low
JL-115W White Baby Blue Low

Part #LED-47B

$2.95  


Click on photo for
larger view
INDICATOR LAMP, #47, T-3-1/4, 6.3V, .15 AMP, BAYONET BASE
P-47
General replacement lamps for dials, indicators, etc. Sold individually.  6.3V.  Fender part number 0021642049
Part #P-47
$0.99  



Click on photo for
larger view

Fender™ Electrolytic Standard OEM Filter Capacitor Kit 24.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Super Reverb Reissue amp, produced from 2000 to the present. 

  • 2 I.C. 100uF-350V (Main Filters)
  • 3 I.C. 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-50V (Cathode Bypass)
  • 6 I.C. 22uF-50V (Cathode Bypass)
  • 1 I.C. 4.7uF-50V (Footswitch Suppression)

Part #FCK-24 (See also FCK-24A, below)

$44.95



Click on photo for
larger view

Fender™ Top Premium Electrolytic Filter Capacitor Kit 24A.  Contains the following capacitors, used as main filters, decoupling filters, bias filter, footswitch suppression, and cathode bypass capacitors in the Fender `65 Super Reverb Reissue amp, produced from 2000 to the present. 

  • 2 F&T 100uF-350V (Main Filters)
  • 3 F&T 22uF-500V (Decoupling Filters)
  • 1 Radial 100uF-100V (Bias Filter)
  • 1 Radial 22uF-50V (Cathode Bypass)
  • 6 Sprague 25uF-25V (Cathode Bypass)
  • 1 Sprague 5uF-50V (Footswitch Suppression)

Part #FCK-24A

$68.95


Click on photo for larger view

CERAMIC 8-PIN WIRED OUTPUT TUBE OR RECTIFIER TUBE SOCKET, crimped bracket, bottom mount 1 1/4", top mount 1" to 1 1/8", 1 1/2" mounting centers, 1" to 1 1/4" chassis hole.  Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.  Click here for additional specs.   Fender part number 0990724000, or 023580.
Part #TS-8-807W

$3.95


Click on photo for
larger view
TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.   Used in Fender™ and many other amps.     1 1/2" mounting centers.  Made by Belton.  Fender part number 099072500.
Part #TC-142
$1.79


Click on photo for
larger view
FENDER STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  INCLUDES INTEGRAL BASE FOR TWIST-LOCK TUBE SHIELD.        Fits 12AX7, 12AU7, 12AT7, etc.   Sturdy Micalex construction, for 3/4"  hole.  Solder tabs for wire connections.   Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TS-325S tube shield, or vintage Fender tube shields.   Used in Fender 65 Super Reverb Reissue.  Fender part number 0023606049.
Part #TS-9-700
$2.69


Click on photo for
larger view
6-PACK OF FENDER STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  INCLUDES INTEGRAL BASE FOR TWIST-LOCK TUBE SHIELD.      Fits 12AX7, 12AU7, 12AT7, etc.   Sturdy Micalex construction, for 3/4"  hole.  Solder tabs for wire connections.   Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TS-325S tube shield, or vintage Fender tube shields.   Used in Fender vintage Blonde, Brownface, Blackface, Silverface and some early Rivera designs.   Also applicable to early Marshall designs.   Pack of 6 tube sockets.  Mounting screws not included - recommend the SC-410-6 screws (2 packs of 6 screws needed for 6 tube sockets).  It is also possible to use 1/8 inch pop rivets to mount these sockets.  Replaces Fender part number 0023606049.
Part #TS-9-700-6
$12.99
(for 6 sockets)


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE .  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes.   9-Pin tube socket is made of sturdy Micalex.   Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   Requires 3/4" hole in chassis.  Solder lugs for wire connection to tube socket. Shield, base and socket
Part #TS-370
$3.99  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.  Includes new base, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.  Shield and base only - socket not included.
 
Part #TS-325S
$1.69  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6.  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   This is a great kit to replaced all 6 of the tube shields in many Fender™ amps with 6 preamp tubes.  Shield and base only - socket not included.
 
Part #TS-325S-6
$8.95  


BLACK FENDER HANDLE
Click on photo for
larger view
ORIGINAL Fender™ GUITAR AMP HANDLE.  Black amplifier handle with vinyl sleeve over steel strap and one-screw mounting nickel-plated end caps.   Includes mounting hardware (two screws and T-nuts).   Used on '65 Super Reverb™.    Original Fender™ part number 0990947000.  
Part #FAH-332
$14.99  


Click on photo for
larger view

Fender™ VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender™ style FAH-332.  See Data Sheet here
Part #SC-403
$0.99
(for a pack of 2 screws)
 


Click on photo for
larger view

Fender™ SELF-TAPPING SCREWS
Used in vintage Fender™ blackface and silverface amps for a variety of tasks.   Used to attach capacitor pans, tube sockets, transformers on smaller amps, chokes, etc.   Pack of 12 screws.  Replaces Fender™ part number 029913.
Part #SC-410-12
$3.50
(for a pack of 12 screws)
 


Click on photo for
larger view
Fender™ Nickel Chassis Straps - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc.  Includes 2 straps, no screws or nuts.  Screw spacing is 5 inches center-to-center, strap length is 5 5/8" end-to-end.
Part #FCS-5-2
$7.95
(Two chassis straps, screws and nuts NOT included)
 



Click on photo for
larger view
Fender™ Chassis Bolt Set - Works with all Fender Nickel or Revisit Chassis Straps for Blackface, Silverface, and reissued Blackface models.   Includes 4 bolts and 4 matching nuts with integral lock washers.  Fender part number 0022236049.
Part #FCB-4
$5.95
(
4 bolts, 4 nuts - complete set for one amp)
 


Click on photo for
larger view
Fender™ AMP "TAIL" LOGO. New original Fender™ reproduction  Fender™ logo with "tail", cast metal, mounting screws included.   Similar to the original logo.  Used on the upper left corner of the grill cloth on most blackface era Fender™ amps.  Approx. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall.  Original Fender™ part number 0994093000
Part #FAL-912
$17.95
(each)
 



Click on photo for
 larger view
Black Logo Mounting Screws
Set of 4 logo mounting screws.  
These are #5 x 7/16" black oxide screws, set of 4.    Fit the AL-921 Ampeg logo, and the Fender FAL-912 logo.
Part #LS-504
$0.99
(for a set of 4 screws)


Click on photo for
larger view
Fender™ style reverb or AC cable clamp.   Used on Fender amps since the early 60s to hold the reverb cable to the side of the cabinet.   Clamp is 3/8" diameter, comes with 3/4" screw for mounting.  Also used in some amplifiers to hold the AC cord to the cabinet wall.  Fender part number 022941.   Works on many other brands of amplifiers as well.
Part #
RCC-381
$0.99  


Click on photo for
larger view
LARGE SIZED STRAIN RELIEF FOR 35/64" X 5/8" HOLE
Popular strain relief found on most vintage guitar amplifiers with round power cords, including most vintage Fender™ amps.   Designed for 5/16" cord diameter.   Click here for specific dimensions of chassis hole.   For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below.
Part #SR-1200
$0.99


Click on photo for
larger view
STRAIN RELIEF INSTALLATION/REMOVAL TOOL
Removing and installing a strain relief can be a frustrating job.   Standard pliers just do not get the job done and can damage the strain relief.   These special strain relief pliers are just what you need.  They fit perfectly on the AC power cord strain relief and give you the leverage you need to compress the strain relief for easy removal and installation, without damage.
Part #YTH-205
$14.95


Click on photo for
larger view
FUSE HOLDER, ORIGINAL Fender™,  FITS MOST LATER MODEL FENDER AMPS    Fits full-size fuse. Chassis mount type with push-on tab connectors.  For standard full size 1.25" X .25" fuses. Fits through a .50" hole in the chassis. As used on the Fender '60s Super Reverb reissue and many other Fender, SWR and other amps. Brand New. Genuine Fender 0036702049. UPC 717669612139. Used on '65 Twin, Hot Rod Deluxe™, Hot Rod DeVille™, Blues Deluxe™, Blues DeVille™, Prosonic™, Vibrosonic, Pro Reverb™, Showman™ 50, '59 Bassman™, Tone Master™, Vibro-King, '63 Fender Tube Reverb and Dual Professional amplifiers Also fits '94 Twin, '65 Super Reverb™, Pro Tube Twin, '64 Vibroverb™, '57 Twin, Super-Sonic™ series, Princeton Recording Amp, Band-Master™ VM Head, Deluxe™ VM, Super Bassman and Super Champ™ XD/X2 amplifiers.
Part #FH-367
$6.49  


(Sold in packs of five fuses.  
1 1/4" long x 1/4" diameter)

FUSE,  Fender™ 4A Slow-Blow. Rated at 4A, for use with '65 Super Reverb Reissue in North America (120V).

Part #MDL-4

$4.95
(Pack of 5 fuses)



Click on photo for
larger view
10 OHM, 5A NTC (Negative Temperature Coefficient) type Thermistor.   Fender part number 028503.    Used in many Fender amp models since the 1990s.  Also used in some Mesa Boogie amps.  It is installed in series in a circuit between the transformer and incoming AC power.   This thermistor is rated for 5A maximum current, and is 19mm in diameter.   By limiting inrush current, it protects the transformer and other components in the power supply at turn-on.   This thermistor should only be used on amps which have a 5 amp fuse or less.   Download data sheet here.
Part #CL-60
$3.99
(each)



Click on photo for
larger view

Genuine Fender™ Footswitch - Vibrato/Reverb

Fender 0994058000 2-Button Vintage-Style Footswitch: Vibrato / Reverb On/Off with 1/4" Jack.  Designed to work with: `65 Twin Reverb Reissue, `63 Vibroverb, `65 Deluxe Reverb Reissue, `65 Super Reverb Reissue, Custom Vibrolux, Vibrasonic.

Part #FBS-360
$64.95  



Click on photo for larger view

Revisit™ Reverb Tank, 17" long, 2 spring, equivalent to Accutronics 4AB3C1B.   Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting.    Replacement for Fender™ '65 Super Reverb Reissue.  Replaces original Fender™ part number 020489.

Up until 2010, Fender™ Super Reverb Reissues used Accutronics Reverb Tanks made in Cary, Illinois.    In November, 2009, the Accutronics company was purchased by Belton, and the manufacturing facility in Cary was closed.   Today, Accutronics tanks are made in Seoul, South Korea.

Revisit™ tanks are manufactured to the same design and detail as the original American-made Accutronics tanks, and we believe that they emulate the sound of the original Accutronics tanks better than the current version of Accutronics tanks made in South Korea.    However, everyone's opinion is different, so we carry both the Revisit™ and the Accutronics brands.

View the 2-year warranty details here.
Part #4AB3C1B

"Bringing back the sound of vintage Accutronics tanks"

$43.79
 

 



Click on photo for larger view

Accutronics Reverb Tank, 17" long, 2 spring, 4AB3C1B.  

Accutronics reverb tanks are a cheaply produced copy of the Belton tank, and are now made by Belton in South Korea.   They are of much lower quality than the original Accutronics reverb tanks made in Cary, Illinois until 2009.

Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down.   This is the Korean-made OEM reverb used in Fender™ '65 Super Reverb Reissues starting in 2010.   Accutronics was purchased by Belton in 2009, and in November of 2009 all production was moved from Cary, Illinois to the Belton manufacturing facility in Seoul, South Korea. 

See explanation of Accutronics reverb tank numbering system here

Part #ACC-4AB3C1B

$39.99  


Click on photo for
larger view

Reverb Tank Bag for 17" tanks.   Used in a variety of amps, including Fender™ amps.  Works with any long (17") reverb tank.   Mounting screws not included.  Reverb bags give the reverb tank better isolation which results is fuller, richer reverb and less feedback.
Part #RB-017
$18.90  


Click on photo for
larger view
TRANSFORMER, Fender™ REVERB DRIVER.  Reverb transformer as found in the Fender™ 65 Twin Reverb Reissue, 65 Super Reverb Reissue, and 65 Deluxe Reverb Reissue.    Fender™ part number 0037099049.  10" leads with .187 faston connectors, X-Mount with 1 3/4" mounting centers. 
Part #037099
$16.95


RESISTOR, FLAMEPROOF, 470 OHM, 2 WATT.    Power tube screen grid resistors in the 65 Super Reverb Reissue.   Original Fender™ part number 036468001. Available individually, or in packs of 5, below.
Part #470FP2
$0.30 each  

RESISTOR, METAL OXIDE FLAMEPROOF, 470 OHM, 2 WATT, PACK OF 5 RESISTORS.    Commonly used as the screen grid resistor in many tube amps including Fender™.  
Part #470FP2-5
$1.15
(Pack of 5 Resistors)
 


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2022 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov